ATTO Technology 2200R/D, 3200R Virtual Device Addressing Method, Logical Unit Addressing Method

Page 45

ATTO Technology, Inc.

ATTO FibreBridge Installation & Operation Manual

parameter allows the host to specify that the peripheral device addressing method will be used regardless of the Addressing Method field in the first level address. This allows custom address translations to be built for systems that may not properly support hierarchical addressing.

Virtual Device Addressing Method

Bit Number

15

14

13

12

11

10

9

8

7

6

5

4

3

2

1

0

0

1

 

 

 

 

 

 

LUN

 

 

 

 

 

 

The LUN field indicates the address of the device to which the command will be routed. The FibreBridge will extract the Bus Number, Target and LUN fields from the LUN based upon parameters contained in FibreBridge non-volatile RAM. The default configuration imposes the following definitions on the LUN field. The SAM-2 specification leaves this to be too arbitrary so again, the FibreBridge default settings are as listed below.

Bit Number

15

14

13

12

11

10

9

8

7

6

5

4

3

2

1

0

0

1

 

 

N/A

 

 

 

LUN

 

 

Target

 

Bus Identifier

Again, the location and width of the Bus, Target and LUN fields are field programmable and are stored in FibreBridge non-volatile RAM. This allows custom address translations to be created to meet special requirements for the customer, operating system, host bus adapter or peripheral device.

Logical Unit Addressing Method

Bit Number

15

14

13

12

11

10

9

8

7

6

5

4

3

2

1

0

1

0

 

 

Target

 

 

Bus Number

 

 

LUN

 

 

The Logical unit address method behaves exactly as the Peripheral device address method with two notable exceptions – field placement and width. The Bus number and Target fields have been moved. The LUN and Target fields are larger and the Bus number field is smaller. The FibreBridge will decode logical unit addressing as described in the peripheral device address method section. Just as with the peripheral and virtual modes, the location and width of the Bus, Target and LUN fields are field programmable. The default mode for Logical Addressing is the same as defined in the SAM-2 specification.

FibreBridge Default Mode

By default, the FibreBridge suppresses the above methods of Hierarchical Addressing and uses its own method, which closely follows the rules of peripheral addressing. This method of addressing is in effect regardless of the Address Method field in the first level address unless you select the option to perform LUN translations.

Bit Number

15

14

13

12

11

10

9

8

7

6

5

4

3

 

2

1

0

0

0

 

 

N/A

 

 

 

LUN

 

 

Target

 

 

Bus

ATTO Technology, Inc.

- 40 -

Image 45
Contents Atto Technology, Inc Atto FibreBridge Atto Technology, Inc Atto Fibrebridge Benefits and Features Updating the Firmware Within the Fibrebridge Atto Technology, Inc Introduction FibreBridge Product Module DescriptionFC Rack System Product Description References Fibre Channel TechnologyAtto FibreBridge Benefits and Features Fibre Channel Switch SupportAtto FibreChain FibreBridge Feature Comparison FeatureAtto FC Rack Enclosure and Power Modules Physical DimensionsMounting Environmental Cooling AirflowCooling Fans Power Module Internal Power DistributionLED Indicator IEC Power Receptacle and SwitchInstallation and Removal Atto FC Rack System Installation Considerations Atto FibreBridge Product Module Integration Power RequirementsAtto FibreBridge Power Connector Scsi Ports Fibre Channel PortsLED Indicators FibreChain Ports 2100 model onlyAtto FibreChain Port LEDs 2100R model only Serial Port Ethernet PortFibreBridge2200R/D Front View FibreBridge 2200R/D2200R/D Side view with hole dimensions Cooling and Airflow Power SupplyScsi Fibre Channel PortLED Indicators on FibreBridge 2200R/D Quick Installation Instructions Cabling a FibreBridgeScsi Cabling Scsi Termination Typical Scsi CablesConnector Laser Type ConnectorFibre Channel Cabling Cable LengthGbic Module and Gbic Guide System Gbic Installation InstructionsGbic Removal Instructions Media Interface Adapters MIAPin # Name MIA Installation MIA DB9 ConnectorAtto BridgeTools Graphical Interface Configuration Program FibreBridge ServicesAccessing the Atto FibreBridge over the RS-232 interface Monitoring and Managing the Atto FibreBridgeSetting up the IP Address using the RS-232 port Accessing the Atto FibreBridge over the Ethernet PortAccessing through FTP Atto Technology, Inc What is Serverless Backup? Serverless Backup SupportEnabling Serverless Backup on the FibreBridge General Operation of Serverless BackupTarget Descriptors Segment DescriptorsFlashing the FibreBridge Updating the Firmware Within the FibreBridgeIdentifying the FibreBridge Addressing Scsi DevicesIdentifying the Scsi Devices Connected to the FibreBridge Default Address Translation Addressing Devices Connected to the FibreBridge Appendix a Fibre Channel to Scsi Address MappingScsi Address Components Fibre Channel AddressingFibre Channel World Wide Name WWN Arbitrated Loop Port Address AlpaBit Scsi Architecture Model SAM-2 Logical Unit AddressingPeripheral Device Addressing Method Bit Number Address Address Method Specific DefinitionFibreBridge Default Mode Virtual Device Addressing MethodLogical Unit Addressing Method SCSI-3 Inquiry Command SCSI-3 Command Changes for Hierarchical Addressing SupportFibre Channel to Scsi Address Mapping Address DescriptorsSCSI-3 Report LUNs Command What to Expect When Setting Device IDsSetting the ID of the FibreBridge Addressing Connected Scsi DevicesAtto Technology, Inc Scsi Device ID Translated LUN as it appears to the Host Configuration for Consecutive IDsAtto Technology, Inc FCC Standards Appendix B Radio and Television InterferenceCanadian Standards European StandardsFurther results of FCC Testing Maximum Height = 1.582 4.015 cm Maximum Height = 1.272 3.228 cm Figure C-3 Atto FibreBridge 3200R Connector Layout Appendix D Fibre Channel Resources Field Replacement Units FRU Appendix E Fibre Channel AccessoriesMIAs Cables/CopperCables/Optical Cables/FibreChainCables/SCSI Appendix F How to Contact Atto Technology, Inc