ATTO Technology 2100R, 2200R/D, 3200R manual Cooling and Airflow, Power Supply

Page 22

ATTO Technology, Inc.

ATTO FibreBridge Installation & Operation Manual

Environmental

The FibreBridge 2200 is designed to operate in an environment that is 0°-40°C, 0-90% humidity and non- condensing.

Cooling and Airflow

There are two fans in the FibreBridge 2200R/D. Each can provide approximately 3 CFM of airflow. Cooling is from side to side where air enters in from the left side and is exhausted out the right. Ambient air near the inlets should not exceed 40°C.

WARNING: DO NOT BLOCK THE VENTS ON EITHER SIDE OF THE MAIN ENCLOSURE. DOING SO MAY CAUSE OVERHEATING AND COULD DAMAGE THE PRODUCT.

Figure 5.5 Cooling Airflow

Power Supply

The FibreBridge 2200R/D contains a universal supply that provides the necessary power for the bridge board and the cooling fans. Refer to the following specifications.

Input voltage: 110/230V AC, with an operating input range of 90-132V AC or 175-264V ac, 47- 63Hz, single phase. The AC input range selection is automatic. No manual jumper or switch over is required.

Output voltage: +12 Volts @ 5 Amps (60 watts) continuous, 5.8 amps (70 watts) peak.

Power Draw: The maximum power draw is 2 Amps @ 110 Volts.

IEC Power Receptacle and Switch

The supply has one standard IEC320 power receptacle and switch. This allows for easy adaptability to different voltage standards throughout the world.

ATTO Technology, Inc.

- 17 -

Image 22
Contents Atto Technology, Inc Atto FibreBridge Atto Technology, Inc Atto Fibrebridge Benefits and Features Updating the Firmware Within the Fibrebridge Atto Technology, Inc FibreBridge Product Module Description IntroductionFC Rack System Product Description Fibre Channel Technology ReferencesFibre Channel Switch Support Atto FibreBridge Benefits and FeaturesAtto FibreChain Feature FibreBridge Feature ComparisonPhysical Dimensions Atto FC Rack Enclosure and Power ModulesMounting Cooling Airflow EnvironmentalCooling Fans Internal Power Distribution Power ModuleIEC Power Receptacle and Switch LED IndicatorInstallation and Removal Atto FC Rack System Installation Considerations Power Requirements Atto FibreBridge Product Module IntegrationAtto FibreBridge Power Connector Fibre Channel Ports Scsi PortsFibreChain Ports 2100 model only LED IndicatorsAtto FibreChain Port LEDs 2100R model only Ethernet Port Serial PortFibreBridge 2200R/D FibreBridge2200R/D Front View2200R/D Side view with hole dimensions Power Supply Cooling and AirflowFibre Channel Port ScsiLED Indicators on FibreBridge 2200R/D Cabling a FibreBridge Quick Installation InstructionsScsi Cabling Typical Scsi Cables Scsi TerminationFibre Channel Cabling ConnectorConnector Laser Type Cable LengthGbic Installation Instructions Gbic Module and Gbic Guide SystemMedia Interface Adapters MIA Gbic Removal InstructionsPin # Name MIA DB9 Connector MIA InstallationAccessing the Atto FibreBridge over the RS-232 interface FibreBridge ServicesAtto BridgeTools Graphical Interface Configuration Program Monitoring and Managing the Atto FibreBridgeAccessing the Atto FibreBridge over the Ethernet Port Setting up the IP Address using the RS-232 portAccessing through FTP Atto Technology, Inc Serverless Backup Support What is Serverless Backup?Target Descriptors General Operation of Serverless BackupEnabling Serverless Backup on the FibreBridge Segment DescriptorsUpdating the Firmware Within the FibreBridge Flashing the FibreBridgeAddressing Scsi Devices Identifying the FibreBridgeIdentifying the Scsi Devices Connected to the FibreBridge Default Address Translation Appendix a Fibre Channel to Scsi Address Mapping Addressing Devices Connected to the FibreBridgeFibre Channel World Wide Name WWN Fibre Channel AddressingScsi Address Components Arbitrated Loop Port Address AlpaScsi Architecture Model SAM-2 Logical Unit Addressing BitBit Number Address Address Method Specific Definition Peripheral Device Addressing MethodVirtual Device Addressing Method FibreBridge Default ModeLogical Unit Addressing Method Fibre Channel to Scsi Address Mapping SCSI-3 Command Changes for Hierarchical Addressing SupportSCSI-3 Inquiry Command Address DescriptorsSetting the ID of the FibreBridge What to Expect When Setting Device IDsSCSI-3 Report LUNs Command Addressing Connected Scsi DevicesAtto Technology, Inc Configuration for Consecutive IDs Scsi Device ID Translated LUN as it appears to the HostAtto Technology, Inc Canadian Standards Appendix B Radio and Television InterferenceFCC Standards European StandardsFurther results of FCC Testing Maximum Height = 1.582 4.015 cm Maximum Height = 1.272 3.228 cm Figure C-3 Atto FibreBridge 3200R Connector Layout Appendix D Fibre Channel Resources MIAs Appendix E Fibre Channel AccessoriesField Replacement Units FRU Cables/CopperCables/FibreChain Cables/OpticalCables/SCSI Appendix F How to Contact Atto Technology, Inc