Tripp Lite Single-Phase 6kVA owner manual Features Rear Panel, Power Module Feature Description

Page 9

Features (Rear Panel) continued

Power Module Feature Description

1.Output Terminal Block (6kVA and 10kVA models only): Use these terminals to connect your power module to your equipment or to the transformer module. Unscrew and remove the cover over the block for access.

2.Input Terminal Block (6kVA and 10kVA models only): Use these terminals to connect your power module to utility power or to the transformer module. Unscrew and remove the cover over the block for access.

3.External Battery Connector: Use this to connect one or more Tripp Lite battery modules to the power module. Remove the cover for access. The power module will not start without a connection to a charged battery module. Refer to the battery module owner’s manual for connection instructions and safety warnings.

4.AC Input Breaker (6kVA and 10kVA models only): One double-pole circuit breaker controls input power to the power module.

5.AC Output Breaker (6kVA and 10kVA models only): One double-pole circuit breaker controls output power from the power module.

6.Exhaust Fan: This cools and ventilates the inside of the power module.

7.Accessory Slot: Remove the small cover panel to install optional accessories to remotely control and monitor your UPS system. Visit Tripp Lite on the Web (www.tripplite.com) to learn about available SNMP, network management and connectivity products that may be installed in this slot.

8.EPO (Emergency Power Off) Port: The power module features an EPO port that may be used to connect the power module to a contact closure switch to enable emergency power off. See “Optional Connection” section for details.

9.RS-232 Communication Port: This female DB9 serial port may be used to connect your UPS to a workstation or server. It uses RS-232 protocol to communicate with a connected computer. It is used with Tripp Lite software and the included serial cable to monitor and manage the UPS remotely over a network and to automatically save open files and shut down equipment during a blackout. See “Optional Connection” for details.

10.Dry Contact Interface Port: This female DB9 port sends contact-closure signals to indicate line-fail and low-battery status. See “Optional Connection” for details.

11.AC Output 1 Breaker (5kVA models only): One double-pole circuit breaker controls output power from the 5kVA power module's AC receptacles labelled "Output 1."

12.AC Output 1 Receptacles (5kVA models only): Accepts direct plug-in connection of NEMA L6-20P equipment plugs.

13.AC Output 2 Receptacles (5kVA models only): Accepts direct plug-in connection of NEMA L6-30P equipment plugs. Either receptacle also accepts direct plug-in connection of transformer connector cable (if used).

14.AC Input Cord (5kVA models only): Connects directly to wall receptacle providing 200/208/220/230 or 240V AC utility power.

Transformer Module Feature Description (Transformer Module not included with hardwire (HV) models.)

15.Utility Input Terminal Block (6kVA and 10kVA models only): Use these terminals to connect your transformer module to utility power. Unscrew and remove the cover over the block for access.

16.Equipment Output Terminal Block (6kVA and 10kVA models only): Use these terminals to connect your equipment to the trans- former module. Unscrew and remove the cover over the block for access.

17.Cable for Power Module Connection (6kVA models only): Connects the transformer module to the power module’s input/output after the power module’s terminal blocks have been removed. See “Connection” section for details.

18 Hardwire Terminal Block for Power Module Connection (10kVA models only): Use these terminals to connect the transformer mod- ule to the power module’s input and output terminal blocks. See “Connection” section for details.

19.Overtemperature Reset Breaker: This circuit breaker trips if the unit’s temperature climbs too high.

20.AC to UPS Breaker (6kVA and 10kVA models only): One double-pole circuit breaker controls the transformer module’s power output to the UPS.

21.Output Breaker (6kVA and 10kVA models only): One triple-pole circuit breaker controls the transformer module’s power output to connected equipment.

22.Manual Bypass Switch (6kVA and 10kVA models only): This red and yellow dial is used to circumvent the power module while still supporting connected equipment when performing power module maintenance. While this switch is on BYPASS, connected equipment will receive filtered AC mains power from the transformer module, but the equipment will not receive battery power in the event of a blackout. See “Manual Bypass Operation” section for complete bypass procedure.

WARNING! For qualified service personnel only. Failure to follow the bypass procedure completely will not

adequately power down the UPS power module, resulting in the continued risk of death or injury from potential

contact with high voltage.

9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Registration WarrantyImportant Safety Warnings Mounting Rack Post MountingPost Telecom Mounting Mounting Tower Power Module Front Panel Controls FeaturesFeatures Rear Panel see page 9 for feature descriptions 6kVA Battery Module 6kVA Power Module 6kVA Transformer ModuleFeatures Rear Panel see page 9 for feature descriptions Power Module Feature Description Features Rear PanelConnection Battery Module Feature DescriptionPlug your equipment into the power module Plug the power module into a wall receptacleConnect the battery module to the power module Plug the transformer module into the power module Hardwire the power module to a utility power source Hardwire the power module to your equipmentConnect the power module to the transformer module Hardwire the transformer module to your equipmentHardwire the transformer module to a utility Power source Select the transformer module’s input voltage Hardwire the power module to the transformer module240V AC RS-232 Serial Communication Connection Optional ConnectionPower ON/OFF 5kVA models only Power ON/OFF 6kVA and 10kVA models only Manual Bypass Operation 6kVA and 10kVA models Only for power module maintenance or replacementOperation Startup Self-TestFailed Self-Test On Battery Alarm Normal OperationOverload Messages Shutdown Messages Bypass MessagesYear Limited Warranty ServiceStorage Regulatory Compliance Identification NumbersSU6000RT3UXR SU10KRT3UHV* & SU10KRT3U SpecificationsManual del propietario Advertencias de seguridad importantes Montaje Bastidor Montaje de 4 postesMontaje de 2 postes Telecomunicaciones Montaje en torre Controles del panel frontal del módulo de potencia CaracterísticasPage Módulo de batería para modelo de 6 kVA Módulo de potencia de 6 kVA Módulo de transformador de 6 kVACaracterísticas Panel posterior Características Panel continuación Descripción de características del módulo de potenciaDescripción de características del módulo del transformador Descripción de características del módulo de batería ConexiónConecte el módulo de batería al módulo de potencia Conecte su equipo en el módulo de potenciaConecte el módulo de transformador en el módulo de potencia Cablee el módulo de potencia a su equipo Cablee el módulo de transformador a su equipo Conecte el módulo de potencia al módulo De transformadorCablee el módulo de potencia al módulo de transformador Seleccione el voltaje de entrada del módulo De transformadorEntrada Interruptor de Interruptores/pantalla Conexión de comunicación serie RS-232 Conexión opcionalEncendido y apagado sólo en modelos de 5 kVA Encendido y apagado Sólo en modelos de 6 kVA y 10 kVA Page Operación Auto-prueba de arranqueFallo durante la auto-prueba Alarma On Battery Operación normalMensajes de sobrecarga Mensajes de apagado Mensajes BypassAlmacenamiento Almacenamiento, Servicio y GarantíaServicio Garantía limitada de 2 añosSU6000RT3UXR EspecificacionesManuel de lutilisateur Consignes de Sécurité Importantes Avertissements pour MaintenanceAvertissements pour Connexion de lEquipement Avertissements pour BatterieMontage Baie Montage à 4 supportsMontage à 2 supports Telecom Montage Tour Caractéristiques Commandes de Panneau Avant de Module dAlimentation2524 Module Batterie pour Modèle 6kVA Module Alimentation 6kVA Module Transformateur 6kVAPage Description des Caractéristiques de Module dAlimentation Caractéristiques Panneau Arrière suiteDescription des Caractéristiques de Module de Batterie ConnexionBranchez votre équipement dans le module Dalimentation Connexion suiteBranchez le module dalimentation dans une prise Murale Branchez le module à piles au module dalimentationConnexion suite Connecter le module de batterie au module dalimentation Câbler le module dalimentation à votre équipementCâbler le module du transformateur à votre équipement Câbler le module dalimentation au module du Transformateur Sélectionner la tension dentrée du module du transformateurSélectionner la tension dentrée du module Du transformateur Connexion Communication Série RS-232 Connexion en OptionAlimentation en Marche/Arrêtée modèles 5kVA seulement Alimentation ON/OFF Modèles 6kVA et 10kVA seulement Opération Bypass Manuelle Modèles 6kVA et 10kVA seulement Fonctionnement Autotest de DémarrageEchec de lAutotest Fonctionnement suite Alarme Sur BatterieFonctionnement Normal Messages de SurchargeMessages de Fermeture Messages de BypassEntreposage Entreposage, Entretien, Garantie et AssuranceEntretien Garantie Limitée à 2 AnsInformation sur le modèle Nos de modèle SpécificationsEnglish/Español/Français Èíñòðóêöèÿ âëàäåëüöàÂàæíàÿ èíñòðóêöèÿ ïî áåçîïàñíîñòè Óñòàíîâêà Ñòåëëàæ Óñòàíîâêà 4-êîíòàêòíîãî ñòåëëàæàÓñòàíîâêà òåëåêîì íà 2õ îñíîâàõ Óñòàíîâêà Áàøíÿ Ïåðåäíÿÿ Ïàíåëü Áëîêà Ïèòàíèÿ ÑâîéñòâàÌîäóëü Áàòàðåè äëÿ ìîäåëåé 6ÊÂÀ è 10ÊÂÀ 6ÊÂÀ Áëîê Ïèòàíèÿ 6ÊÂÀ Ìîäóëü Èçîëèðóþùèé Òðàíñôîðìàòîð2120 Ñâîéñòâà Çàäíÿÿ Ïàíåëü ïðîäîëæåíèå Îïèñàíèå Ñâîéñòâ Áëîêà ïèòàíèÿ ìîäåëè 6ÊÂÀ è 10ÊÂÀÎïèñàíèå Ñâîéñòâ Ìîäóëÿ Áàòàðåè 6ÊÂÀ è 10ÊÂÀ Ñîåäèíèòå âàø ìîäóëü ïèòàíèÿ ñ îáîðóäîâàíèåì ÑîåäèíåíèåÑîåäèíèòå áëîê ïèòàíèÿ ñ èñòî÷íèêîì ýëåêòðîýíåðãèè Ñîåäèíèòå ìîäóëü áàòàðåè ñ ìîäóëÿìè áëîêà ïèòàíèÿÑîåäèíèòå ìîäóëü áëîêà ïèòàíèÿ ñ ìîäóëåì Òðàíñôîðìàòîðà Ñîåäèíåíèå ïðîäîëæåíèåÑîåäèíèòå ìîäóëü òðàíñôîðìàòîðà ñ âàøèì Îáîðóäîâàíèåì Ñîåäèíèòå ìîäóëü òðàíñôîðìàòîðà ñ èñòî÷íèêîìÑîåäèíèòå ìîäóëü áàòàðåè ñ ìîäóëåì òðàíñôîðìàòîðà Âûáåðèòå íàïðÿæåíèå ââîäà íà ìîäóëå òðàíñôîðìàòîðàÑîåäèíèòå âàø ìîäóëü òðàíñôîðìàòîðà ñ Îáîðóäîâàíèåì Ñâÿçü ÷åðåç Óíèâåðñàëüíûé Ñåðèéíûé Ïîðò USB RS-232 Äîïîëíèòåëüíîå ñîåäèíåíèåÂÊËÞ×ÈÒÜ/ÂÛÊËÞ×ÈÒÜ Page Ïðàâèëà Ïîëüçîâàíèÿ Ñàìîñòîÿòåëüíûé Ïðîâåðî÷íûé Òåñò ÑòàðòàÑàìîñòîÿòåëüíûé ïðîâåðî÷íûé òåñò íå ïðîéäåí Íîðìàëüíîå Ïîëüçîâàíèå Ïðàâèëà Ïîëüçîâàíèÿ, ïðîäîëæåíèåÇâóêîâîé Ñèãíàë Îò Áàòàðåè Ñîîáùåíèÿ î ÏåðåãðóçêåÑîîáùåíèÿ ïî îòêëþ÷åíèþ Ñîîáùåíèå î Ðåæèìå Ïåðåìû÷êèÑåðâèñ/Ãàðàíòèÿ ÑåðâèñÎãðàíè÷åííàÿ 2õ ëåòíÿÿ ãàðàíòèÿ SU6000RT3UXR ÑïåöèôèêàöèèTh Street Chicago, IL 60609 USA BP Series External Battery Packs Introduction Post Mounting Mounting RackConnection Internal Battery Replacement TroubleshootingService StorageRegulatory Compliance Identification Numbers Year Limited WarrantyManual del propietario Introducción Montaje de 4 postes Montaje BastidorMontaje en bastidor continúa Reemplazo de batería interna Solución de problemasAlmacenamiento ServicioCondiciones Garantía limitada de 2 añosManuel de lutilisateur Consignes de Sécurité Importantes Conserver ces Instructions Montage à 4 supports Montage BaieMontage Baie suite Remplacement de batterie interne DépannageStockage Numéros didentification de conformité aux règlements Garantie limitée à 2 ansÐóêîâîäñòâî ïîëüçîâàòåëÿ Ââåäåíèå Ìîíòàæ Ñòåëëàæ Ìîíòàæ íà ñòîéêå ñ 2 îïîðàìè Telecom Ìîíòàæ Ñòåëëàæ ïðîäîëæåíèåÒåõíè÷åñêîå îáñëóæèâàíèå Ãàðàíòèéíûå îáÿçàòåëüñòâà
Top Page Image Contents