Moxa Technologies EDS-510A user manual Protocol of Redundancy, Bridge priority, Forwarding Delay

Page 45

EDS-510A Series User’s Manual

Featured Functions

At the bottom of this page, the user can configure the “Settings” of this function. For RSTP, you can configure:

Protocol of Redundancy

Setting

Description

Factory Default

Turbo Ring

Select this item to change to the Turbo Ring

None

 

configuration page.

 

RSTP (IEEE 802.1W/1D)

Select this item to change to the RSTP

None

 

configuration page.

 

Bridge priority

 

 

 

 

 

Setting

Description

Factory Default

Numerical value selected

Increase this device’s bridge priority by

32768

by user

selecting a lower number. A device with a

 

 

higher bridge priority has a greater chance of

 

 

being established as the root of the Spanning

 

 

Tree topology.

 

Forwarding Delay

 

 

Setting

Description

Factory Default

Numerical value input by

The amount of time this device waits before

15 (sec.)

user

checking to see if it should change to a

 

 

different state.

 

Hello time (sec.)

 

 

 

 

 

Setting

Description

Factory Default

Numerical value input by

The root of the Spanning Tree topology

2

user

periodically sends out a “hello” message to

 

 

other devices on the network to check if the

 

 

topology is healthy. The “hello time” is the

 

 

amount of time the root waits between sending

 

 

hello messages.

 

Max. Age (sec.)

 

 

 

 

 

Setting

Description

Factory Default

Numerical value input by

If this device is not the root, and it has not

20

user

received a hello message from the root in an

 

 

amount of time equal to “Max. Age,” then this

 

 

device will reconfigure itself as a root. Once

 

 

two or more devices on the network are

 

 

recognized as a root, the devices will

 

 

renegotiate to set up a new Spanning Tree

 

 

topology.

 

Enable STP per Port

 

 

 

 

 

Setting

Description

Factory Default

Enable/Disable

Select to enable the port as a node on the

Disabled

 

Spanning Tree topology.

 

3-30

Page 44 Page 46
Image 45
Page 44 Page 46
Contents First Edition, October Moxa EtherDevice Switch EDS-510A Series User’s ManualCopyright Notice TrademarksDisclaimer Table of Contents Chapter EDS Configurator GUI Introduction Features Package ChecklistOverview Industrial Networking CapabilityRecommended Software and Accessories Useful Utility and Remote ConfigurationGetting Started Connection Caution RS-232 Console Configuration 115200, None, 8, 1, VT100EDS-510A Series User’s Manual Key Function Configuration using a Telnet Console Configuration using a Web Browser EDS-510A Series User’s Manual Disabling Telnet and Browser Access Featured Functions System Identification Configuring Basic SettingsPassword PasswordAccount Any host on a specific subnetwork can access the EDS-510A Accessible IPAny host can access the EDS-510A Allowable Hosts Input formatPort EnableDescription NameNetwork SpeedFDX Flow Ctrl Switch IP Address Auto IP ConfigurationSwitch Subnet Mask Default GatewayCurrent Time TimeCurrent Date System Up TimeTime zone before setting the time Turbo Ring DIP SwitchTime Server IP/Name Time Server Query PeriodDIP Switch Turbo Ring DIP Description DIP Switch Hardware ConfigurationConfiguration Files Path and Name System File Update-By Remote TftpTftp Server IP/Name Firmware Files Path and NameSystem File Update-By Backup Media System File Update-By Local Import/ExportUsing Port Trunking Factory DefaultRestart Port Trunking Concept Configuring Port Trunking Trunk Group Maximum of 3 trunk groupsTrunk Type Setting Description Configuring SnmpAvailable Ports/Member Port Trunk TableSnmp Versions V1, V2c Read CommunityV1, V2c Write/Read Community 1st Trap Server IP/Name Trap SettingsUsing Communication Redundancy Private MIB informationGigabit Ethernet Redundant Ring Capability 300 ms Turbo Ring Concept Initial SetupWhen the number of EDS-510A units in the Turbo Ring is even Ring Coupling Configuring Turbo Ring STP/RSTP Concept Following explanation uses bridge instead of switch What is STP?STP Requirements How STP WorksPort Speed Path Cost 802.1D Edition 802.1w-2001 STP CalculationSTP Reconfiguration STP ConfigurationDifferences between Rstp and STP STP ExampleUsing STP on a Network with Multiple VLANs Root/Not Root Configuring STP/RSTPEnable STP per Port Forwarding DelayProtocol of Redundancy Bridge priorityPort Priority Configuration Limits of RSTP/STPPort Cost Port StatusWhat is Traffic Prioritization? Using Traffic PrioritizationTraffic Prioritization Concept How Traffic Prioritization WorksDifferentiated Services DiffServ Traffic Marking Ieee 802.1p Priority Level Ieee 802.1D Traffic TypeTraffic Prioritization Configuring Traffic Prioritization QoS ClassificationTraffic Queues Port Highest Priority Queuing MechanismInspect TOS Inspect COSSetting Description Factory CoS MappingTOS/DiffServ Mapping What is a VLAN? Using Virtual LANVirtual LAN Vlan Concept Benefits of VLANsManaging a Vlan VLANs and Moxa EtherDevice SwitchCommunication Between VLANs VLANs Tagged and Untagged MembershipDevice Sample Applications of VLANs using Moxa EDS-510AVlan Settings Configuring Virtual LANManagement Vlan ID Vlan ModePort Type Port PvidPort Vlan TableWhat is an IP Multicast? Using Multicast FilteringConcept of Multicast Filtering Benefits of MulticastMulticast Filtering and Moxa EtherDevice Switch Igmp Internet Group Management Protocol Snooping ModeNetwork without multicast filtering Igmp Multicast Filtering Query ModeGmrp Garp Multicast Registration Protocol Static Multicast MACIgmp Snooping Settings Configuring Igmp SnoopingAdd Static Multicast MAC Configuring Gmrp Using Bandwidth ManagementGmrp enable Gmrp TableTraffic Rate Limiting Settings Using Port Access ControlStatic Port Lock IeeeMessage Exchange Configuring Ieee Configuring Static Port LockRadius Server Database OptionServer Port Shared KeyLocal User Database Setup 802.1X Re-Authentication802.1X Re-Authentication Local User Database SetupUsing Auto Warning Configuring Email WarningPort Access Control Table Event Type System EventsPort Events Password Setting Email SetupMail Server IP/Name Account NameEvent Setup Configuring Relay WarningEmail Address Send Test EmailSystem Events Using Set Device IP Using Line-Swap-Fast-RecoveryConfiguring Line-Swap Fast Recovery Override relay alarm settingsSet up the connected devices Configuring Set Device IPMirror Port Using DiagnosisOutput data stream Bi-directionalUsing Monitor Monitor by SwitchPing Monitor by Port Using the MAC Address TableMAC Using Event LogUsing Syslog Using HTTPS/SSLSyslog Settings EDS-510A Series User’s Manual Featured Functions EDS Configurator GUI Broadcast Search Starting EDS ConfiguratorSearch by IP address Modify IP Address Upgrade FirmwareExport Configuration Import Configuration Locked Unlock ServerUnlocked BlankFixed Locked FixedUnlocked Fixed MIB Groups MIB II.10 Transmission Group MIB II.11 Snmp GroupMIB II.17 dot1dBridge Group Private Traps Public TrapsSpecifications TechnologyInterface Mechanical EnvironmentalRegulatory Approvals Service Information Following services are provided Moxa Internet ServicesSerial Number Problem Report FormProduct Return Procedure

EDS-510A, Moxa EtherDevice Switch specifications

Moxa Technologies is a leader in providing innovative networking solutions for industrial applications, and one of its standout products is the Moxa EtherDevice Switch, EDS-510A. This robust, managed Ethernet switch is specifically designed for reliable performance in challenging industrial environments, making it an ideal choice for various applications, including automation, transportation, and power generation.

The EDS-510A features five 10/100Base-TX Fast Ethernet ports, allowing flexibility in connecting multiple devices. Additionally, it offers two Gigabit Ethernet ports for uplink, enabling high-speed connections to aggregation switches or routers. The switch supports both redundant power inputs and a wide operating temperature range of -40 to 75 degrees Celsius, ensuring continuity of service even in extreme conditions.

One of the key features of the EDS-510A is its support for IEEE 802.3at PoE (Power over Ethernet). This technology allows the switch to deliver power to connected devices such as IP cameras and wireless access points through the Ethernet cable, which simplifies installation and reduces the need for additional power sources. This is especially beneficial in remote locations where power availability may be limited.

The EDS-510A is also equipped with advanced management features that include VLAN support, port mirroring, and QoS (Quality of Service) capabilities. These features enhance network performance and security, enabling users to prioritize critical traffic and segment the network for better control. Moreover, it supports SNMP (Simple Network Management Protocol), allowing for easy integration into existing network management systems.

Another notable characteristic is the switch's rugged design. With a metal housing that provides excellent EMI (Electromagnetic Interference) protection, the EDS-510A can withstand harsh industrial environments. It is also compliant with various industrial standards, reinforcing its suitability for mission-critical applications.

In summary, the Moxa EtherDevice Switch, EDS-510A, is engineered to meet the demands of modern industrial networking. With its combination of PoE capability, advanced management features, and rugged design, it ensures reliable and efficient network performance, making it an excellent choice for organizations looking to enhance their industrial networking infrastructure. Whether deployed in factories, transportation systems, or utility environments, the EDS-510A continues to be a trusted solution for numerous applications.
Top Page Image Contents