Moxa Technologies EDS-510A user manual Configuring Set Device IP, Set up the connected devices

Page 75

EDS-510A Series User’s Manual

Featured Functions

effect, the EDS-510A acts as a DHCP server by assigning a connected device with a specific IP address stored in its internal memory. Each time the connected device is switched on or rebooted, the EDS-510A sends the device the desired IP address.

Perform the following steps to use the Set device IP function:

STEP 1—set up the connected devices

Set up those Ethernet-enabled devices connected to the EDS-510A for which you would like IP addresses to be assigned automatically. The devices must be configured to obtain their IP address automatically.

The devices’ configuration utility should include a setup page that allows you to choose an option similar to Obtain an IP address automatically.

For example, Windows’ TCP/IP Properties window is shown at the right. Although your device’s configuration utility may look quite a bit different, this figure should give you some idea of what to look for.

You also need to decide to which of the EDS-510A’s ports your Ethernet-enabled devices will be connected. You will need to set up each of these ports separately, as described in the following step.

STEP 2

Configure the EDS-510A’s Set device IP function, either from the Console utility or from the Web Browser interface. In either case, you simply need to enter the Desired IP for each port that needs to be configured.

STEP 3

Be sure to activate your settings before exiting.

•When using the Web Browser interface, activate by clicking Activate.

•When using the Console utility, activate by first highlighting the Activate menu option, and then press Enter. You should receive the Set device IP settings are now active! (Press any key to continue) message.

Configuring Set Device IP

3-60

Page 74 Page 76
Image 75
Page 74 Page 76
Contents First Edition, October Moxa EtherDevice Switch EDS-510A Series User’s ManualCopyright Notice TrademarksDisclaimer Table of Contents Chapter EDS Configurator GUI Introduction Industrial Networking Capability Package ChecklistFeatures OverviewRecommended Software and Accessories Useful Utility and Remote ConfigurationGetting Started Connection Caution RS-232 Console Configuration 115200, None, 8, 1, VT100EDS-510A Series User’s Manual Key Function Configuration using a Telnet Console Configuration using a Web Browser EDS-510A Series User’s Manual Disabling Telnet and Browser Access Featured Functions System Identification Configuring Basic SettingsPassword PasswordAccount Allowable Hosts Input format Accessible IPAny host on a specific subnetwork can access the EDS-510A Any host can access the EDS-510AName EnablePort DescriptionNetwork SpeedFDX Flow Ctrl Default Gateway Auto IP ConfigurationSwitch IP Address Switch Subnet MaskSystem Up Time TimeCurrent Time Current DateTime Server Query Period Turbo Ring DIP SwitchTime zone before setting the time Time Server IP/NameDIP Switch Turbo Ring DIP Description DIP Switch Hardware ConfigurationFirmware Files Path and Name System File Update-By Remote TftpConfiguration Files Path and Name Tftp Server IP/NameSystem File Update-By Backup Media System File Update-By Local Import/ExportUsing Port Trunking Factory DefaultRestart Port Trunking Concept Configuring Port Trunking Trunk Group Maximum of 3 trunk groupsTrunk Type Trunk Table Configuring SnmpSetting Description Available Ports/Member PortSnmp Versions V1, V2c Read CommunityV1, V2c Write/Read Community 1st Trap Server IP/Name Trap SettingsUsing Communication Redundancy Private MIB informationGigabit Ethernet Redundant Ring Capability 300 ms Turbo Ring Concept Initial SetupWhen the number of EDS-510A units in the Turbo Ring is even Ring Coupling Configuring Turbo Ring STP/RSTP Concept Following explanation uses bridge instead of switch What is STP?STP Calculation How STP WorksSTP Requirements Port Speed Path Cost 802.1D Edition 802.1w-2001STP Example STP ConfigurationSTP Reconfiguration Differences between Rstp and STPUsing STP on a Network with Multiple VLANs Root/Not Root Configuring STP/RSTPBridge priority Forwarding DelayEnable STP per Port Protocol of RedundancyPort Status Configuration Limits of RSTP/STPPort Priority Port CostHow Traffic Prioritization Works Using Traffic PrioritizationWhat is Traffic Prioritization? Traffic Prioritization ConceptDifferentiated Services DiffServ Traffic Marking Ieee 802.1p Priority Level Ieee 802.1D Traffic TypeTraffic Prioritization Configuring Traffic Prioritization QoS ClassificationTraffic Queues Inspect COS Queuing MechanismPort Highest Priority Inspect TOSSetting Description Factory CoS MappingTOS/DiffServ Mapping Benefits of VLANs Using Virtual LANWhat is a VLAN? Virtual LAN Vlan ConceptVLANs Tagged and Untagged Membership VLANs and Moxa EtherDevice SwitchManaging a Vlan Communication Between VLANsDevice Sample Applications of VLANs using Moxa EDS-510AVlan Settings Configuring Virtual LANPort Pvid Vlan ModeManagement Vlan ID Port TypePort Vlan TableBenefits of Multicast Using Multicast FilteringWhat is an IP Multicast? Concept of Multicast FilteringMulticast Filtering and Moxa EtherDevice Switch Igmp Internet Group Management Protocol Snooping ModeNetwork without multicast filtering Static Multicast MAC Query ModeIgmp Multicast Filtering Gmrp Garp Multicast Registration ProtocolIgmp Snooping Settings Configuring Igmp SnoopingAdd Static Multicast MAC Gmrp Table Using Bandwidth ManagementConfiguring Gmrp Gmrp enableIeee Using Port Access ControlTraffic Rate Limiting Settings Static Port LockMessage Exchange Configuring Ieee Configuring Static Port LockShared Key Database OptionRadius Server Server PortLocal User Database Setup 802.1X Re-AuthenticationLocal User Database Setup 802.1X Re-AuthenticationUsing Auto Warning Configuring Email WarningPort Access Control Table Event Type System EventsPort Events Account Name Email SetupPassword Setting Mail Server IP/NameSend Test Email Configuring Relay WarningEvent Setup Email AddressSystem Events Override relay alarm settings Using Line-Swap-Fast-RecoveryUsing Set Device IP Configuring Line-Swap Fast RecoverySet up the connected devices Configuring Set Device IPBi-directional Using DiagnosisMirror Port Output data streamUsing Monitor Monitor by SwitchPing Monitor by Port Using the MAC Address TableMAC Using Event LogUsing Syslog Using HTTPS/SSLSyslog Settings EDS-510A Series User’s Manual Featured Functions EDS Configurator GUI Broadcast Search Starting EDS ConfiguratorSearch by IP address Modify IP Address Upgrade FirmwareExport Configuration Import Configuration Blank Unlock ServerLocked UnlockedFixed Locked FixedUnlocked Fixed MIB Groups MIB II.10 Transmission Group MIB II.11 Snmp GroupMIB II.17 dot1dBridge Group Private Traps Public TrapsSpecifications TechnologyInterface Mechanical EnvironmentalRegulatory Approvals Service Information Following services are provided Moxa Internet ServicesSerial Number Problem Report FormProduct Return Procedure

EDS-510A, Moxa EtherDevice Switch specifications

Moxa Technologies is a leader in providing innovative networking solutions for industrial applications, and one of its standout products is the Moxa EtherDevice Switch, EDS-510A. This robust, managed Ethernet switch is specifically designed for reliable performance in challenging industrial environments, making it an ideal choice for various applications, including automation, transportation, and power generation.

The EDS-510A features five 10/100Base-TX Fast Ethernet ports, allowing flexibility in connecting multiple devices. Additionally, it offers two Gigabit Ethernet ports for uplink, enabling high-speed connections to aggregation switches or routers. The switch supports both redundant power inputs and a wide operating temperature range of -40 to 75 degrees Celsius, ensuring continuity of service even in extreme conditions.

One of the key features of the EDS-510A is its support for IEEE 802.3at PoE (Power over Ethernet). This technology allows the switch to deliver power to connected devices such as IP cameras and wireless access points through the Ethernet cable, which simplifies installation and reduces the need for additional power sources. This is especially beneficial in remote locations where power availability may be limited.

The EDS-510A is also equipped with advanced management features that include VLAN support, port mirroring, and QoS (Quality of Service) capabilities. These features enhance network performance and security, enabling users to prioritize critical traffic and segment the network for better control. Moreover, it supports SNMP (Simple Network Management Protocol), allowing for easy integration into existing network management systems.

Another notable characteristic is the switch's rugged design. With a metal housing that provides excellent EMI (Electromagnetic Interference) protection, the EDS-510A can withstand harsh industrial environments. It is also compliant with various industrial standards, reinforcing its suitability for mission-critical applications.

In summary, the Moxa EtherDevice Switch, EDS-510A, is engineered to meet the demands of modern industrial networking. With its combination of PoE capability, advanced management features, and rugged design, it ensures reliable and efficient network performance, making it an excellent choice for organizations looking to enhance their industrial networking infrastructure. Whether deployed in factories, transportation systems, or utility environments, the EDS-510A continues to be a trusted solution for numerous applications.
Top Page Image Contents