Moxa Technologies Moxa EtherDevice Switch, EDS-510A Using the MAC Address Table, Monitor by Port

Page 78

EDS-510A Series User’s Manual

Featured Functions

Monitor by Port

Access the Monitor by Port function by selecting ALL 10/100M or 1G Ports or Port i, in which i= 1, 2, …, G2, from the left pull-down list. The Port i options are identical to the Monitor by System function discussed above, in that users can view graphs that show All Packets, TX Packets, RX Packets, or Error Packets activity, but in this case, only for an individual port. The All Ports option is essentially a graphical display of the individual port activity that can be viewed with the Console Monitor function discussed above. The All Ports option shows three vertical bars for each port. The height of the bar represents Packets/s for the type of packet, at the instant the bar is being viewed. That is, as time progresses, the height of the bar moves up or down so that the user can view the change in the rate of packet transmission. The blue colored bar shows Unicast packets, the red colored bar shows Multicast packets, and the orange colored bar shows Broadcast packets. The graph is updated every few seconds, allowing the user to analyze data transmission activity in real-time.

Using the MAC Address Table

This section explains the information provided by the EDS-510A’s MAC address table.

The MAC Address table can be configured to display the following EDS-510A MAC address groups.

ALL

Select this item to show all EDS-510A MAC addresses

ALL Learned

Select this item to show all EDS-510A Learned MAC addresses

ALL Static Lock

Select this item to show all EDS-510A Static Lock MAC addresses

ALL Static

Select this item to show all EDS-510A

Static/Static Lock /Static

 

Multicast MAC addresses

 

ALL Static

Select this item to show all EDS-510A

Static Multicast MAC

Multicast

addresses

 

Port x

Select this item to show all MAC addresses of dedicated ports

3-63

Image 78
Contents Moxa EtherDevice Switch EDS-510A Series User’s Manual First Edition, OctoberCopyright Notice TrademarksDisclaimer Table of Contents Chapter EDS Configurator GUI Introduction Overview Package ChecklistFeatures Industrial Networking CapabilityUseful Utility and Remote Configuration Recommended Software and AccessoriesGetting Started RS-232 Console Configuration 115200, None, 8, 1, VT100 Connection CautionEDS-510A Series User’s Manual Key Function Configuration using a Telnet Console Configuration using a Web Browser EDS-510A Series User’s Manual Disabling Telnet and Browser Access Featured Functions Configuring Basic Settings System IdentificationPassword PasswordAccount Any host can access the EDS-510A Accessible IPAny host on a specific subnetwork can access the EDS-510A Allowable Hosts Input formatDescription EnablePort NameNetwork SpeedFDX Flow Ctrl Switch Subnet Mask Auto IP ConfigurationSwitch IP Address Default GatewayCurrent Date TimeCurrent Time System Up TimeTime Server IP/Name Turbo Ring DIP SwitchTime zone before setting the time Time Server Query PeriodDIP Switch Hardware Configuration DIP Switch Turbo Ring DIP DescriptionTftp Server IP/Name System File Update-By Remote TftpConfiguration Files Path and Name Firmware Files Path and NameSystem File Update-By Local Import/Export System File Update-By Backup MediaUsing Port Trunking Factory DefaultRestart Port Trunking Concept Configuring Port Trunking Trunk Group Maximum of 3 trunk groupsTrunk Type Available Ports/Member Port Configuring SnmpSetting Description Trunk TableSnmp Versions V1, V2c Read CommunityV1, V2c Write/Read Community Trap Settings 1st Trap Server IP/NameUsing Communication Redundancy Private MIB informationGigabit Ethernet Redundant Ring Capability 300 ms Initial Setup Turbo Ring ConceptWhen the number of EDS-510A units in the Turbo Ring is even Ring Coupling Configuring Turbo Ring STP/RSTP Concept What is STP? Following explanation uses bridge instead of switchPort Speed Path Cost 802.1D Edition 802.1w-2001 How STP WorksSTP Requirements STP CalculationDifferences between Rstp and STP STP ConfigurationSTP Reconfiguration STP ExampleUsing STP on a Network with Multiple VLANs Configuring STP/RSTP Root/Not RootProtocol of Redundancy Forwarding DelayEnable STP per Port Bridge priorityPort Cost Configuration Limits of RSTP/STPPort Priority Port StatusTraffic Prioritization Concept Using Traffic PrioritizationWhat is Traffic Prioritization? How Traffic Prioritization WorksDifferentiated Services DiffServ Traffic Marking Ieee 802.1p Priority Level Ieee 802.1D Traffic TypeTraffic Prioritization Configuring Traffic Prioritization QoS ClassificationTraffic Queues Inspect TOS Queuing MechanismPort Highest Priority Inspect COSSetting Description Factory CoS MappingTOS/DiffServ Mapping Virtual LAN Vlan Concept Using Virtual LANWhat is a VLAN? Benefits of VLANsCommunication Between VLANs VLANs and Moxa EtherDevice SwitchManaging a Vlan VLANs Tagged and Untagged MembershipSample Applications of VLANs using Moxa EDS-510A DeviceConfiguring Virtual LAN Vlan SettingsPort Type Vlan ModeManagement Vlan ID Port PvidVlan Table PortConcept of Multicast Filtering Using Multicast FilteringWhat is an IP Multicast? Benefits of MulticastMulticast Filtering and Moxa EtherDevice Switch Igmp Internet Group Management Protocol Snooping ModeNetwork without multicast filtering Gmrp Garp Multicast Registration Protocol Query ModeIgmp Multicast Filtering Static Multicast MACConfiguring Igmp Snooping Igmp Snooping SettingsAdd Static Multicast MAC Gmrp enable Using Bandwidth ManagementConfiguring Gmrp Gmrp TableStatic Port Lock Using Port Access ControlTraffic Rate Limiting Settings IeeeMessage Exchange Configuring Static Port Lock Configuring IeeeServer Port Database OptionRadius Server Shared Key802.1X Re-Authentication 802.1X Re-AuthenticationLocal User Database Setup Local User Database SetupUsing Auto Warning Configuring Email WarningPort Access Control Table Event Type System EventsPort Events Mail Server IP/Name Email SetupPassword Setting Account NameEmail Address Configuring Relay WarningEvent Setup Send Test EmailSystem Events Configuring Line-Swap Fast Recovery Using Line-Swap-Fast-RecoveryUsing Set Device IP Override relay alarm settingsConfiguring Set Device IP Set up the connected devicesOutput data stream Using DiagnosisMirror Port Bi-directionalUsing Monitor Monitor by SwitchPing Using the MAC Address Table Monitor by PortUsing Event Log MACUsing Syslog Using HTTPS/SSLSyslog Settings EDS-510A Series User’s Manual Featured Functions EDS Configurator GUI Starting EDS Configurator Broadcast SearchSearch by IP address Upgrade Firmware Modify IP AddressExport Configuration Import Configuration Unlocked Unlock ServerLocked BlankFixed Locked FixedUnlocked Fixed MIB Groups MIB II.10 Transmission Group MIB II.11 Snmp GroupMIB II.17 dot1dBridge Group Public Traps Private TrapsSpecifications TechnologyInterface Mechanical EnvironmentalRegulatory Approvals Service Information Moxa Internet Services Following services are providedProblem Report Form Serial NumberProduct Return Procedure

EDS-510A, Moxa EtherDevice Switch specifications

Moxa Technologies is a leader in providing innovative networking solutions for industrial applications, and one of its standout products is the Moxa EtherDevice Switch, EDS-510A. This robust, managed Ethernet switch is specifically designed for reliable performance in challenging industrial environments, making it an ideal choice for various applications, including automation, transportation, and power generation.

The EDS-510A features five 10/100Base-TX Fast Ethernet ports, allowing flexibility in connecting multiple devices. Additionally, it offers two Gigabit Ethernet ports for uplink, enabling high-speed connections to aggregation switches or routers. The switch supports both redundant power inputs and a wide operating temperature range of -40 to 75 degrees Celsius, ensuring continuity of service even in extreme conditions.

One of the key features of the EDS-510A is its support for IEEE 802.3at PoE (Power over Ethernet). This technology allows the switch to deliver power to connected devices such as IP cameras and wireless access points through the Ethernet cable, which simplifies installation and reduces the need for additional power sources. This is especially beneficial in remote locations where power availability may be limited.

The EDS-510A is also equipped with advanced management features that include VLAN support, port mirroring, and QoS (Quality of Service) capabilities. These features enhance network performance and security, enabling users to prioritize critical traffic and segment the network for better control. Moreover, it supports SNMP (Simple Network Management Protocol), allowing for easy integration into existing network management systems.

Another notable characteristic is the switch's rugged design. With a metal housing that provides excellent EMI (Electromagnetic Interference) protection, the EDS-510A can withstand harsh industrial environments. It is also compliant with various industrial standards, reinforcing its suitability for mission-critical applications.

In summary, the Moxa EtherDevice Switch, EDS-510A, is engineered to meet the demands of modern industrial networking. With its combination of PoE capability, advanced management features, and rugged design, it ensures reliable and efficient network performance, making it an excellent choice for organizations looking to enhance their industrial networking infrastructure. Whether deployed in factories, transportation systems, or utility environments, the EDS-510A continues to be a trusted solution for numerous applications.