TOA Electronics FPS1000-12, FPS1000-24, FPS1000-32, FPS-S1U, FPS-T1U FPS1000 Series Specifications

CHAPTER 1 FPS1000 SERIES SPECIFICATIONS

	FPS1000 SERIES SPECIFICATIONS			FPS1000-12		FPS1000-24			FPS1000-32	FPS1000-48
1	Rated output voltage		V	12		24		32		48
2	Output voltage set point		V	12+/-1%		24+/-1%		32+/-1%		48+/-1%
3	Output voltage range		V	10.5~13.2		21.5~29		28.8~38.4		43~58
4	Maximum Output Current (Refer to Fig.1)		A	72		40		31		21
5	Maximum output power		W	864		960		992		1008
6	Input voltage / frequency range	(*1)	---			85~265Vac continuous, 47~63Hz, Single phase
7	Maximum input current (at 100/200Vac)		A				12.0/6.0
8	Power Factor (Typ)		---		>0.98 at 115/230V and maximum output power
9	Efficiency (Typ)	(*2)	%	81/83%		84/86%			84/86%	85/88%
10	Inrush current	(*3)	A			Less than 40A
11	Hold-up time		mS	20mS typical at 100Vac input, rated output voltage and less than 80% of rated load.
12	Maximum line regulation	(*5)	---				0.40%
13	Max load regulation	(*6)	---				0.80%
14	Output Ripple and noise pk-pk	(*4)	mV	150		200			250	300
15	Temperature stability		---	0.05% of rated Vout for 8hrs after 30min warm-up. Constant line, load and temperature.
16	Temperature coefficient		PPM/°C				200
17	Remote sensing	(*7)	V			Possible. Refer to Instruction Manual.
18	Parallel operation	(*9)	---			Possible. Refer to Instruction Manual.
19	Series operation		---			Possible. Refer to Instruction Manual.
20	Over current protection		---		105~125% of maximum output current. Refer to Fig. 1
21	Over voltage protection	(*8)	V	14.3~15.7	31~34				41.5~45.5	62~66
22	Over temperature protection		---			Inverter shut down method, automatic reset.
23	Remote On/Off control		---	By electrical signal or dry contact. ON: 0~0.6V or short. OFF: 2~15V or open.
24	DC OK signal		---	Open collector signal. On when Vout>80+/-5% rated output. Max.sink current: 10mA
25	Over-Temp. warning		---		Open collector signal. Refer to Instruction Manual
26	AC fail signal		---		Open collector signal. Refer to Instruction Manual
27	Auxiliary power supply		---			11.2~12.5VDC. 0.25A Maximum output current.
28	Vout voltage trimming		---	Possible, via Vout Trim pin in the I/O connector. Refer to Instruction Manual.
29	Front panel indicators		---			AC OK, DC OK, DC FAIL
30	I2C Interface		---			Optional. Refer to Instruction Manual.
31	Operating temperature-models without IEC inlet		---	0~50°C: 100% load. Derate 2%/°C, 50°C to 60°C, Derate 2.5%/°C, 60°C to 70°C.
	models with IEC inlet		---		0~50°C: 100% load. Derate 2%/°C, 50°C to 60°C.
32	Storage temperature		---				-30~85°C
33	Operating humidity		---			10~90% RH, no condensation.
34	Storage humidity		---			10~95% RH, no condensation.
35	Cooling		---			By internal Fans. Variable speed control.
36	Vibration		---			Built to meet ETS 300 019
37	Shock		---			Built to meet ETS 300 019
38	Conducted emission	(*10)	---			EN55022B, FCC part 15J-B, VCCI-B
39	Radiated emission		---			EN55022B, FCC part 15J-B, VCCI-B
40	Applicable safety standards		---			UL60950-1, EN60950-1
41	Withstand voltage		---	Input-Output: 3000Vrms, 1min. Input-Ground: 2000Vrms, 1min. Output-Ground: 500Vrms,1min.
42	Insulation resistance		---	More than 100Mohm at 25° C and 70% RH. Output-Ground: 500Vdc
43	Leakage current		mA			Less Than 1.1mA at 230Vac
44	Weight (Typ)		Kg				2.0
45	Size (W*H*D)		---			127x41x290mm. Refer to Outline Drawing.

Notes:

*1: For cases where conformance to various safety standards (UL, EN etc.) is required, to be described as 100-240Vac (50/60Hz).

*2: At 100/200Vac, rated load and 25˚C ambient temperature.

*3: Not applicable for the noise filter inrush current less than 0.2mS.

*4: Measured with JEITA RC-9131A 1:1 probe, 20MHz B.W.

*5: From 85~132Vac or 170~265Vac, constant load.

*6: From No-load to Rated load, constant input voltage. Measured at the sensing point in Remote sense.

*7: Remote sensing can compensate up to 1V drop on each load wire.

*8: Inverter shut down method. Reset by AC voltage recycle or by On/Off control.

*9: Derate Maximum output power by 10% for input voltage less than 100V RMS.

*10 For FPS 1000-12/P(S), when used not with FPS-S1U or FPS-T1U racks, an EMI suppressor clamp should be attached to the AC cable, as close as possible to the AC inlet, to meet class B.

Vout (V)

V2

Model	FPS1000	FPS1000	FPS1000	FPS1000
V/I	-12	-24	-32	-48
V1 (V)	12	24	32	48
V2 (V)	13.2	29	38.4	58
I1 (A)	66	33	26	17.25
I2 (A)	72	40	31	21

V1

I1 I2 Iout (A)

Fig. 1: Rated output current vs output voltage

4