NTI VEEMUX VIDEO MATRIX SWITCH
Command Definitions (Cont'd)
| Command |
|
| Good Response |
|
| Description |
|
|
|
|
|
|
| |||
| String |
|
|
|
|
|
|
|
| RS SW |
| *<CR> |
| Internal Reset | |||
| RV SW,00 |
| *<CR>string\0<CR> | Read NTI Version String | ||||
| RU SW |
| *<CR>IP,OP<CR> | Read Unit Size | ||||
| EA SW,ip |
| *<CR> |
| Set the IP address, ip is in xxx.xxx.xxx.xxx format, | |||
|
|
|
|
|
|
| number of digits is minimum 1 and maximum 3 for each field | |
|
|
|
|
|
|
| Leading zeroes are accepted | |
| EM SW,ip | *<CR> |
| Set the Subnet mask, ip is in xxx.xxx.xxx.xxx format, | ||||
|
|
|
|
|
|
| number of digits is minimum 1 and maximum 3 for each field. | |
|
|
|
|
|
|
| Leading zeroes are accepted | |
| EG SW,ip | *<CR> |
| Set the default gateway, ip is in xxx.xxx.xxx.xxx format, | ||||
|
|
|
|
|
|
| number of digits is minimum 1 and maximum 3 for each field | |
|
|
|
|
|
|
| Leading zeroes are accepted | |
| ET SW,timeout |
| *<CR> |
| Set the website timeout; timeout = numeric string of timeout in seconds. | |||
|
|
|
|
|
|
| Values: 60, 300, 600, 900, 1800, 3600, 7200, 18000, 28800 | |
|
|
|
|
|
|
| 0 = no timeout | |
| RA SW * |
| <CR>ip<CR> |
| Read the IP address, ip is in xxx.xxx.xxx.xxx format, | |||
|
|
|
|
|
|
| number of digits is minimum 1 and maximum 3 for each field | |
|
|
|
|
|
|
| Leading zeroes are accepted | |
| RM SW * |
| <CR>ip<CR> |
| Read the Subnet mask, ip is in xxx.xxx.xxx.xxx format, | |||
|
|
|
|
|
|
| number of digits is minimum 1 and maximum 3 for each field | |
|
|
|
|
|
|
| Leading zeroes are accepted | |
| RG SW * |
| <CR>ip<CR> |
| Read the default gateway, ip is in xxx.xxx.xxx.xxx format, | |||
|
|
|
|
|
|
| number of digits is minimum 1 and maximum 3 for each field | |
|
|
|
|
|
|
| Leading zeroes are accepted | |
| RT SW * |
| <CR>timeout<CR> |
| Read the website timeout; timeout = numeric value in seconds. | |||
|
|
|
|
|
|
| Values: 60, 300, 600, 900, 1800, 3600, 7200, 18000, 28800 | |
|
|
|
|
|
|
| 0 = no timeout | |
|
|
|
|
| ||||
| SS SW,00 | *<CR> |
| Disable Autostatus feature (see below) | ||||
| SS SW,01 | *<CR> |
| Enable Autostatus feature (see below) | ||||
| GO SW,OP | *<CR>go SW,OP,IP<CR> | Read connection of a Output Port to Input Port | |||||
| GM SW,00 | *<CR>go SW,OP,IP (all |
| Read connection matrix of all Output ports | ||||
|
|
|
| ports)<CR> |
|
|
| |
| Ss SW,OP,DWT |
| *<CR> |
| Set Scan Mode dwell time for specific Output port | |||
|
|
|
|
|
|
| DWT values: | |
| Gs SW,OP |
| *<CR> |
| Read scan mode dwell time setting for an Output port | |||
|
|
|
| DWT<CR> |
| DWT values: | ||
| Sa SW,OP | *<CR> | Set scan list of individual output to all inputs | |||||
| Sc SW,OP | *<CR> | Clear scan list of individual output | |||||
| S+ SW,OP,IP | *<CR> | Add individual input to Scan List of output | |||||
| S- SW,OP,IP | *<CR> | Remove individual input from Scan List of output | |||||
| Sx SW,OP | *<CR>oooxoxxxooooxxx< |
| Inspect the Scan List of individual output (o=skip x=don't skip) | ||||
|
|
|
| CR> |
|
|
| |
If the first field is not a known command (as listed above) or SW field is different from the serial address programmed in the switch memory, the command will be ignored. If the SW field corresponds to the unit address, but the syntax is wrong after this field, the switch will answer with a bad response ?<CR>.
Autostatus
When Autostatus is enabled, any
Example of an Autostatus message:
pc 01,01:04<CR>
which means "At the switch with unit address 01, the output (01) has changed connection to input 04."
Notes: Message to the administrator will be delayed by any RS232 traffic being received by the switch from the administrator.
Autostatus must be disabled before using SerTest or the Matrix Switcher's Control Program (below).
By default, Autostatus is disabled and must be manually enabled. Autostatus is also disabled any time the power to the VEEMUX is interrupted.
10