Network Technologies SM-nXm-15V-LCD Introduction, Basic Operation, Supported Web Browsers

Page 5

NTI VEEMUX VIDEO MATRIX SWITCH

INTRODUCTION

The SM-nXm-15V-LCD (n = number of inputs (video sources), m = number of outputs (monitors)) video matrix switch (VEEMUX) allows any of up to 32 video sources to output to any or all of up to sixteen (16) monitors. The configuration of the VEEMUX is determined at time of order (i.e. 16x4, 8x16, etc.). The bandwidth of the SM-nXm-15V-LCD is 200MHz and video resolutions through 1900 x1200 are supported with no degradation. The switch can be controlled with the Front Panel Keypad, RS232 interface, Ethernet, or an optional Infrared Remote.

The VEEMUX can be ordered in many sizes and with several control options. The base unit includes a user keypad, an RS232 port, and an Ethernet port to make up a complete system. The infrared option, purchased separately, allows for maximum user satisfaction in each unique configuration.

Basic Operation

The VEEMUX allows any source to be connected to any destination at any time with no restrictions or limitations.

Video inputs accept any RGBHV, RGBS, or RGsB signal.

Video outputs are compatible with any RGBHV or RGBS monitor, regardless of input. (RGsB monitor requires RGsB input)

Supported Web Browsers

Most modern web browsers should be supported. The following browsers have been tested:

Microsoft Internet Explorer 6.0 or higher

Netscape 7.0 or higher

Mozilla FireFox 0.9.2 or higher

Set your browser to always check if there is a newer version of the page than the version stored in cache. This action will ensure that it will display the most up-to-date information.

Compatibilty

The SM-nXm-15V-LCD is made to support video inputs from VGA (15HD – H & V Sync) only.

Ordering Information

The SM-nXm-15V-LCD is built to a specific size ranging from 2, 4, 8, 12, or 16 monitors and 4 to 32 video sources. The “n” in the part number represents the number of video sources. Select a switch built for 4, 8, 16, or 32 video sources. The “m” in the part number represents the number of outputs (monitors). A switch built for 2, 4, 8, 12, or 16 monitors may be ordered. It is not necessary to fully populate all of the connectors on the unit (ex. an SM-16x8 switch has the capability of supporting 16 video sources and 8 monitors, but it will operate with only 14 video sources with 7 monitors connected.

SM-nXm-15V-LCD

Replace the “n” with 4,8,16, or 32

Replace the “m” with either 2, 4 ,8,12,or 16

The following list represents the available sizes that can be ordered:

SM-4x2-15V-LCD

SM-8x2-15V-LCD

SM-16x2-15V-LCD

SM-32x2-15V-LCD

SM-4x2-15V-LCD-DT*

SM-8x2-15V-LCD-DT*

SM-16x4-15V-LCD

SM-32x4-15V-LCD

SM-4x4-15V-LCD-DT* SM-8x4-15V-LCD

SM-16x8-15V-LCD

SM-32x8-15V-LCD

SM-4x4-15V-LCD

SM-8x4-15V-LCD-DT*

SM-16x12-15V-LCD

SM-32x16-15V-LCD

 

SM-8x8-15V-LCD

SM-16x16-15V-LCD

 

*-DT = Desktop chassis instead of rack mount chassis

Options

DDC Support (see page 28)

This feature makes the DDC information of the monitor connected to port 1 available to each CPU.

This feature is ordered by adding a "D" following the size designation in the model number (i.e. SM-8X2D-15V-LCD)

Infrared Control (see page 23)

This feature adds the ability to control the VEEMUX via an infrared remote.

This feature is ordered by adding the suffix "-IR" to the model number when ordering (i.e. SM-4X2-15V-LCD-IR)

1

Image 5
Contents SM-nXm-15V-LCD Trademark Table of Contents Table of Figures Basic Operation IntroductionSupported Web Browsers CompatibiltyMaterials Default User Name and PasswordsCables Materials Supplied with this kitFront View of SM-8X8-15V-LCD Features and FunctionsPower ON/OFF switch Connect the Sources and Monitors InstallationConnect to the Ethernet 9D-male RS232 connectorConnect RS232 LED Matrix Power UpFront Panel LCD with Keypad Control Control OptionsEscape back to the main display Used to enter numbers. # Output user number can be enteredRemote Connection Scan ModeRS232 Control Baud Rate Command ProtocolUnit Address RS232 Matrix-Y-1 CPU Serial PortAutostatus Command Definitions ContdMatrix Operations SerTest- RS232 Interface Test ProgramMain Options Ethernet Operations Setup OptionsEthernet Control Command Reply DescriptionTelnet Interface Telnet 192.168.1.30Web Interface Enter the PasswordWeb interface Switch Video SwitchWeb interface Setup Setup PagesVideo Input Names Web interface Serial SetupOutput Names Scan ModeWeb interface Update Firmware Update FirmwareHelp Change PasswordUpdate Web Server Web interface Logout LogoutDevice Discovery Tool Device Discovery ToolInfrared Control Features And FunctionsKeypad LCD DisplayPower on with SYS, in or OUT keys Power on with 2 key How To Use The IRTChange the Switch Change Input Port Change Output PortSet Configuration Specifications Battery ReplacementIRT Troubleshooting Insert 2 new AA cell batteriesDDC Support Following will be needed RS232 Upgrade of the Front Panel LCD FirmwareNTI Veemux Video Matrix Switch Pinout of RS232 port on Veemux RS232 Connection CablesArrows indicate signal direction Wiring Schematic of Matrix-Y-1 cablePinout for Matrix Y-1 Cable Rack Mounting InstructionsNTI Desktop Size Rack Units Rack Size In. WxDxH SpecificationsSafety Statements TroubleshootingWarranty Information Index