Network Technologies SM-nXm-15V-LCD Infrared Control, Features And Functions, Keypad, LCD Display

Page 27

NTI VEEMUX VIDEO MATRIX SWITCH

INFRARED CONTROL

(Optional)

The IRT-64X32 (or IRT) is an infrared remote transmitter that enables the user to control up to four (4) NTI VEEMUX Video Matrix switches via an infrared receiver from up to 50 feet away (with an unobstructed view). The IRT is battery-powered and always ready to use. The IRT will have a blank display unless an action is being selected by the user. The IRT enables the user to

make connections between any input (video source) and any output (display device) on up to four (4) separate switches.

Note: Multiple switches that are located close to each other and are to be individually controlled must be pre-configured (by NTI) to be identified by the IRT as switches #1, #2, #3, or #4. Please ask your salesperson to have switches configured accordingly at time of order. Unless otherwise specified, by default, all IRT-enabled switches will be configured as switch #1.

Materials included:

•IRT-64X32 Infrared Remote Transmitter for video matrix switches

•(2) AA Cell Batteries- installed

Features And Functions

Keypad

¾Buttons Numbered 0-9 – Used for port selection

¾OUT – Pressed to validate and transmit the Output selection

¾IN – Pressed to validate and transmit the Input selection

¾SYS – Pressed to choose the switch to be controlled or to configure the maximum number of inputs/outputs

NTI R

Network Technologies Inc

SW

Lo Batt

1 2 3

4 5 6

7 8 9

OUT 0 IN

SYS

IRT-64X32

LCD Display

¾The first digit of the LCD will display the number of the switch to be controlled followed by the decimal point. This way the user will always know which switch will be effected by the IRT.

¾The last two digits in the LCD represent 1) the desired input or output port to be connected or 2) the desired switch to be controlled when changing switches.

¾The "Lo Batt" decimal point will illuminate when the user should change the batteries.

¾The LCD will automatically power-down after 30 seconds of non-use and power-up with the press of any button.

Represents Input or

Output

SW

Lo Batt

Represents switch to be controlled

23

Page 26 Page 28
Image 27
Page 26 Page 28
Contents SM-nXm-15V-LCD Trademark Table of Contents Table of Figures Compatibilty IntroductionBasic Operation Supported Web BrowsersMaterials Supplied with this kit Default User Name and PasswordsMaterials CablesFeatures and Functions Power ON/OFF switchFront View of SM-8X8-15V-LCD Connect the Sources and Monitors Installation9D-male RS232 connector Connect RS232Connect to the Ethernet LED Matrix Power UpOutput user number can be entered Control OptionsFront Panel LCD with Keypad Control Escape back to the main display Used to enter numbers. #Scan Mode RS232 ControlRemote Connection RS232 Matrix-Y-1 CPU Serial Port Command ProtocolBaud Rate Unit AddressAutostatus Command Definitions ContdSerTest- RS232 Interface Test Program Main OptionsMatrix Operations Ethernet Operations Setup OptionsTelnet 192.168.1.30 Command Reply DescriptionEthernet Control Telnet InterfaceWeb Interface Enter the PasswordWeb interface Switch Video SwitchWeb interface Setup Setup PagesVideo Input Names Web interface Serial SetupOutput Names Scan ModeWeb interface Update Firmware Update FirmwareChange Password Update Web ServerHelp Web interface Logout LogoutDevice Discovery Tool Device Discovery ToolLCD Display Features And FunctionsInfrared Control KeypadHow To Use The IRT Change the SwitchPower on with SYS, in or OUT keys Power on with 2 key Change Input Port Change Output PortSet Configuration Insert 2 new AA cell batteries Battery ReplacementSpecifications IRT TroubleshootingDDC Support Following will be needed RS232 Upgrade of the Front Panel LCD FirmwareNTI Veemux Video Matrix Switch Pinout of RS232 port on Veemux RS232 Connection CablesRack Mounting Instructions Wiring Schematic of Matrix-Y-1 cableArrows indicate signal direction Pinout for Matrix Y-1 CableNTI Desktop Size Rack Units Rack Size In. WxDxH SpecificationsIndex TroubleshootingSafety Statements Warranty Information
Top Page Image Contents