Paradyne Routers manual MIBs Overview, Standard MIBs, Mib Ii Rfc, System Group

Page 75

Traps & MIBs

MIBs Overview

The Hotwire DSL system supports standard as well as Paradyne Enterprise MIBs. Various configuration, status, and statistical data within the SNMP agent is accessible from the NMS. The content of an SNMP agent's MIBs is defined by various Internet Request for Comments (RFC) documents.

The following sections provide brief descriptions about supported MIBs. Complete, up-to-date details about the content of all DSL MIBs are available on the Paradyne Web site at www.paradyne.com. Select Technical Support MIBs.

Standard MIBs

Standard MIBs supported consist of the following:

HRFC 1213: MIB II

HRFC 1573: Evolution of the Interfaces Group

HRFC 2096: IP Forwarding Table MIB

HRFC 2665: Ethernet-Like MIB

MIB II (RFC 1213)

The objects defined by MIB II (RFC 1213) are organized into ten groups:

HSystem Group ± fully supported. Refer to System Group

HInterfaces Group ± refer to Interfaces Group (RFC 1573) and Extension to Interfaces Table (RFC 1573)

HAddress Translation Group ± not supported.

HIP Group ± refer to IP Group (RFC 1213) and IP CIDR Route Group (RFC 2096)

HICMP Group ± fully supported.

HTCP Group ± fully supported.

HUDP Group ± fully supported.

HEGP Group ± not supported.

HTransmission Group ± refer to Transmission Group.

HSNMP Group ± refer to SNMP Group.

System Group

System Group objects are fully supported by the DSL router, as shown in

Table C-2.

6371-A2-GB20-10

August 2000

C-3

Image 75
Contents HOTWIRE DSL Routers Copyright E 2000 Paradyne Corporation All rights reserved Contents Configuring the DSL Router Monitoring the DSL Router Index Document Purpose and Intended Audience About This GuideSection Description Document SummaryDocument Number Document Title Product-Related DocumentsSyntax Translation Document ConventionsIntroduction to Hotwire DSL Routers What is a Hotwire DSL Router?DSL Technologies Supported Network Access Provider NAP Typical DSL Router SystemOptional IP routing with Hotwire DSL Router FeaturesService Subscriber Accessing the DSL Router Access Control to the DSL RouterLevels of Access Show console Changing Access Session LevelsLocal Console Access Admin enableSetting Up the New Users Login CUSTOMER#. Type configure terminal and press EnterInvalid Characters Value Ascii Hex Translation Local console disabled by conflict Telnet AccessDetermining the Current Access Level Determining the Available CommandsUsing the List Command Exiting from the SystemChanging the System Identity If you are accessing the DSL router Then Manually Logging OutAutomatically Logging Out Configuring the DSL Router Overview of DSL Router ConfigurationInterfaces for the DSL Router Ethernet and DSL Interface Identifiers Service Domain IP Address AssignmentsNumbered DSL Interface Unnumbered DSL InterfaceSimplified Network Topology Network Considerations IP RoutingProxy ARP Address Resolution Protocol ARPNetwork Address Translation NAT Basic NATNetwork Address Port Translation Napt Dynamic Host Configuration Protocol Dhcp Server IP Options ProcessingApplications Supported by NAT Dhcp Relay Agent Security IP FilteringLand Bug/Smurf Attack Prevention Routed vs. Bridged PDUs Routed Network Model Standard modeConfiguration Examples DSL Router Configuration ExamplesCustomer Premises CP Basic Configuration ExampleNAT Mapping Public IP Addresses Private IP Addresses Basic NAT Configuration ExampleNapt Mapping Public IP Addresses Private IP Addresses Napt Configuration ExampleCore Router 155.1.3.253 Console Port Connection Dhcp Relay with Proxy ARP Configuration Example Public IP Addresses for Basic NAT Private IP Addresses Dhcp Server with Basic NAT Configuration ExampleDownstream Router Configuration Example Detecting Problems Monitoring the DSL RouterWhat to Monitor ± Ethernet Link up down Status of InterfacesShow interface Show interface eth1 dsl1Interface Statistics Show statisticsShow statistics eth1 dsl1 ip Discard Reasons for the Ethernet Interface eth1 1 Clearing StatisticsList of Discard Reasons Clear statistics eth1 dsl1 ipDiscard Reasons for the DSL Interface dsl1 1 Discard Reasons for the Ethernet Interface eth1 2Discard Reasons for IP Discard Reasons for the DSL Interface dsl1 2Show alarms Diagnostics and TroubleshootingDiagnostics and Troubleshooting Overview Alarms InquirySyslog ip ip-addr Syslog enable disableSystem Log Show syslogSyslog Messages 1 Level Description Event Syslog EventsSyslog level level Show log numberSyslog Message Display Syslog Messages 2 Level Description EventReporting Ping reply x.x.x.x Request Timed OUT PingPing Test Results Ping reply x.x.x.x bytes of data=nnTraceRoute TraceRoute Test ResultsX.x Command Line Interface Feature Command Line InterfaceCommand Recall NavigationDocument Conventions Ethernet Frame Format Command Line Interface CommandsConfiguration Control Commands RFC 1483 EncapsulationInterface and Service Domain IP Address IP Routing Table Delete eth1ifn dsl1ifnIp route create dest-ipdest-mask next-hop-ip remote Ip route purge Proxy ARP ARP TableNat basic address ip-addrip-mask Nat basic enableNat napt enable Nat timeout timeNat napt delete udp tcp port Nat basic delete private-ipNat purge Nat disableDhcp server enable disable Dhcp ServerDhcp Relay Agent IP Packet Processing IP multicast enable disableIP processing enable disable Trap disable enable name of trapShow Command Outputs Show configNAT disabled or NAT enabled basic NAT Napt Show arp Show arp timeoutNAT timeout xx minutes NAT basic mappings Show ip route ip-addressShow NAT napt Show trapsShow dhcp server Sample show dhcp relay display Show alarms Show syslog Show log #Show Dhcp relay Show interface Show statisticsConfiguration Default Settings Configuration Defaults Command Line ShortcutsCustomer ParadyneAbc123 BytesTable B-2. Command Line Input Shortcuts 1 Command Line Input ShortcutsTable B-2. Command Line Input Shortcuts 2 Show interface dsl1 eth1 Table B-2. Command Line Input Shortcuts 3Configuration Defaults & Command Line Shortcuts Traps & MIBs Snmp OverviewTraps Overview Variable Binding DSL Router TrapsSystem Group MIBs OverviewStandard MIBs MIB II RFCSystem Ssssssssssss Boot bb.bb.bb 2nd Boot xx.xx.xx DSPYy.yy.yy H/W Releasezzz CCA part numberº Interfaces Group RFCInterfaces IfEntryIfOperStatus Specifies the current DSL interface Table C-5. IP Group Objects 1 Description Setting/Contents Extension to Interfaces Table RFCIP Group RFC IP Cidr Route Group RFC Table C-5. IP Group Objects 2 Description Setting/ContentsIpCidrRouteEntry 11 ± Transmission GroupEthernet-Like MIB RFC Snmp GroupActive1 Paradyne Enterprise MIBsDevice Control MIB NoOp1Device Diagnostics MIB Traceroute ApplpingTestEntryConfigure ApplTracerouteResultsEntryAppTracerouteResultsEntry Health and Status MIB DevStatus1DevStatus Factory1-to-active8 Configuration MIBSecondary Interface Configuration MIBPdnInetIpAddressTableEntry PrimaryDhcp MIB DSL Endpoint MIB Syslog MIB Accessing the List Command Output DSL Router Terminal EmulationDSL Router Terminal Emulation Terminal Emulation Programs Numbers IndexIN-2 IN-3