Paradyne Routers manual IP Packet Processing, Traps, IP multicast enable disable

Page 62

Command Line Interface

IP Packet Processing

IP multicast { enable disable}

Enables or disables the forwarding of IP multicast packets. This setting is retained across power cycles.

Minimum access level: Administrator

enable ± Enable forwarding of IP multicast packets.

disable ± Disable forwarding of IP multicast packets. Default = disable.

IP processing { enable disable}

Enables or disables the processing of IP packets in the service domain. This setting is retained across power cycles.

Minimum access level: Administrator

enable ± Enable processing of IP packets. Default = enable. disable ± Disable processing of IP packets.

Traps

trap {disable enable} name of trap

Use this command to enable or disable traps. Default = disable.

Minimum access level: Administrator/Config

Name of Traps:

all

authen fail ccn devfail link up link down selftest test start test stop warmstart

For additional information, refer to Appendix C, Traps & MIBs.

A-12

August 2000

6371-A2-GB20-10

Image 62

Contents HOTWIRE DSL Routers Copyright E 2000 Paradyne Corporation All rights reserved Contents Configuring the DSL Router Monitoring the DSL Router Index About This Guide Document Purpose and Intended AudienceDocument Summary Section DescriptionProduct-Related Documents Document Number Document TitleDocument Conventions Syntax TranslationDSL Technologies Supported Introduction to Hotwire DSL RoutersWhat is a Hotwire DSL Router? Optional Network Access Provider NAPTypical DSL Router System Hotwire DSL Router Features IP routing withService Subscriber Levels of Access Accessing the DSL RouterAccess Control to the DSL Router Admin enable Changing Access Session LevelsLocal Console Access Show consoleInvalid Characters Value Ascii Hex Translation Setting Up the New Users LoginCUSTOMER#. Type configure terminal and press Enter Determining the Available Commands Telnet AccessDetermining the Current Access Level Local console disabled by conflictChanging the System Identity Using the List CommandExiting from the System Automatically Logging Out If you are accessing the DSL router ThenManually Logging Out Interfaces for the DSL Router Configuring the DSL RouterOverview of DSL Router Configuration Service Domain IP Address Assignments Ethernet and DSL Interface IdentifiersSimplified Network Topology Numbered DSL InterfaceUnnumbered DSL Interface IP Routing Network ConsiderationsAddress Resolution Protocol ARP Proxy ARPNetwork Address Port Translation Napt Network Address Translation NATBasic NAT Applications Supported by NAT Dynamic Host Configuration Protocol Dhcp ServerIP Options Processing Dhcp Relay Agent Land Bug/Smurf Attack Prevention SecurityIP Filtering Routed Network Model Standard mode Routed vs. Bridged PDUsDSL Router Configuration Examples Configuration ExamplesBasic Configuration Example Customer Premises CPBasic NAT Configuration Example NAT Mapping Public IP Addresses Private IP AddressesNapt Configuration Example Napt Mapping Public IP Addresses Private IP AddressesCore Router 155.1.3.253 Console Port Connection Dhcp Relay with Proxy ARP Configuration Example Dhcp Server with Basic NAT Configuration Example Public IP Addresses for Basic NAT Private IP AddressesDownstream Router Configuration Example What to Monitor Detecting ProblemsMonitoring the DSL Router Show interface eth1 dsl1 Status of InterfacesShow interface ± Ethernet Link up downShow statistics eth1 dsl1 ip Interface StatisticsShow statistics Clear statistics eth1 dsl1 ip Clearing StatisticsList of Discard Reasons Discard Reasons for the Ethernet Interface eth1 1Discard Reasons for the Ethernet Interface eth1 2 Discard Reasons for the DSL Interface dsl1 1Discard Reasons for the DSL Interface dsl1 2 Discard Reasons for IPAlarms Inquiry Diagnostics and TroubleshootingDiagnostics and Troubleshooting Overview Show alarmsShow syslog Syslog enable disableSystem Log Syslog ip ip-addrShow log number Syslog EventsSyslog level level Syslog Messages 1 Level Description EventReporting Syslog Message DisplaySyslog Messages 2 Level Description Event Ping reply x.x.x.x bytes of data=nn PingPing Test Results Ping reply x.x.x.x Request Timed OUTX.x TraceRouteTraceRoute Test Results Command Line Interface Command Line Interface FeatureDocument Conventions Command RecallNavigation RFC 1483 Encapsulation Command Line Interface CommandsConfiguration Control Commands Ethernet Frame FormatInterface and Service Domain IP Address Ip route create dest-ipdest-mask next-hop-ip remote IP Routing TableDelete eth1ifn dsl1ifn Ip route purge ARP Table Proxy ARPNat timeout time Nat basic enableNat napt enable Nat basic address ip-addrip-maskNat basic delete private-ip Nat napt delete udp tcp portDhcp Server Nat disableDhcp server enable disable Nat purgeDhcp Relay Agent Trap disable enable name of trap IP multicast enable disableIP processing enable disable IP Packet ProcessingNAT disabled or NAT enabled basic NAT Napt Show Command OutputsShow config Show ip route ip-address Show arp timeoutNAT timeout xx minutes NAT basic mappings Show arpShow dhcp server Show NAT naptShow traps Show interface Show statistics Show alarms Show syslog Show log #Show Dhcp relay Sample show dhcp relay displayConfiguration Defaults Command Line Shortcuts Configuration Default SettingsBytes ParadyneAbc123 CustomerCommand Line Input Shortcuts Table B-2. Command Line Input Shortcuts 1Table B-2. Command Line Input Shortcuts 2 Table B-2. Command Line Input Shortcuts 3 Show interface dsl1 eth1Configuration Defaults & Command Line Shortcuts Traps Overview Traps & MIBsSnmp Overview DSL Router Traps Variable BindingMIB II RFC MIBs OverviewStandard MIBs System GroupSsssssssssss Boot bb.bb.bb 2nd Boot xx.xx.xx DSP SystemIfEntry Interfaces Group RFCInterfaces Yy.yy.yy H/W Releasezzz CCA part numberºIfOperStatus Specifies the current DSL interface IP Group RFC Table C-5. IP Group Objects 1 Description Setting/ContentsExtension to Interfaces Table RFC Table C-5. IP Group Objects 2 Description Setting/Contents IP Cidr Route Group RFCTransmission Group IpCidrRouteEntry 11 ±Snmp Group Ethernet-Like MIB RFCNoOp1 Paradyne Enterprise MIBsDevice Control MIB Active1Device Diagnostics MIB ApplpingTestEntry TracerouteAppTracerouteResultsEntry ConfigureApplTracerouteResultsEntry DevStatus Health and Status MIBDevStatus1 Configuration MIB Factory1-to-active8Primary Interface Configuration MIBPdnInetIpAddressTableEntry SecondaryDhcp MIB DSL Endpoint MIB Syslog MIB DSL Router Terminal Emulation Accessing the List Command OutputDSL Router Terminal Emulation Terminal Emulation Programs Index NumbersIN-2 IN-3