Paradyne Routers manual IP Routing Table, Delete eth1ifn dsl1ifn

Page 55

Command Line Interface

delete {eth1[:ifn] dsl1[:ifn] }

Deletes any of the assignments that are configured for the interface. Only the specific

Ethernet or DSL interface number needs to be specified.

An interface address and mask cannot be deleted while there is a static route (upstream or downstream) that uses it. First, delete the IP route with the ip route delete command (see IP Routing Table).

Minimum access level: Administrator/Config

eth1, eth1:1, eth1:2, eth1:3, eth1:4 ± Ethernet interface. eth1 is the same as eth1:1.

dsl1, dsl1:1, dsl1:2, dsl1:3, dsl1:4 ± DSL interface. dsl1 is the same as dsl1:1. Only dsl1 or dsl1:1 are acceptable inputs for an unnumbered interface.

Example: delete eth1:4

IP Routing Table

ip route create dest-ipdest-mask{ next-hop-ip remote}

ip route delete dest-ip dest-mask

Configures the downstream static routes. Downstream routes cannot be created unless at least one Ethernet interface has been configured. To configure upstream routers, refer to the next set of entries.

create ± Create a downstream IP route table entry. To configure a downstream default gateway, enter a destination IP address and a subnet mask of 0.0.0.0.

delete ± Delete a downstream IP route table entry. This will delete an IP route placed in the table by the DHCP server, the DHCP relay, or manually entered static entries.

NOTE: An interface route is created automatically when an address and mask are assigned to an Ethernet interface with the ifn address command. The Ethernet interface route can be deleted with the ip route purge or the ip route delete command. Once deleted, the interface route can be entered manually using ip route create or a new ifn address command.

dest-ip± IP address of the destination. The destination IP address must be within the address range of a configured Ethernet interface or the next-hop-ip address must be provided.

dest-mask± IP mask for the destination IP address.

next-hop-ip± IP address of the next hop downstream router used to reach the destination. A next hop with an IP address of 0.0.0.0 specifies a directly reachable client. A nonzero next-hop-ip address must be within the address range of an Ethernet interface.

remote ± Indicates that the device specified by the destination IP and destination mask is logically within a local subnet route but is not on the physical Ethernet and resides upstream from the DSL router. A remote route cannot be created unless at least one DSL interface has previously been configured.

Example: Refer to Chapter 4, DSL Router Configuration Examples.

6371-A2-GB20-10

August 2000

A-5

Image 55
Contents HOTWIRE DSL Routers Copyright E 2000 Paradyne Corporation All rights reserved Contents Configuring the DSL Router Monitoring the DSL Router Index Document Purpose and Intended Audience About This GuideSection Description Document SummaryDocument Number Document Title Product-Related DocumentsSyntax Translation Document ConventionsWhat is a Hotwire DSL Router? Introduction to Hotwire DSL RoutersDSL Technologies Supported Typical DSL Router System Network Access Provider NAPOptional IP routing with Hotwire DSL Router FeaturesService Subscriber Access Control to the DSL Router Accessing the DSL RouterLevels of Access Show console Changing Access Session LevelsLocal Console Access Admin enableCUSTOMER#. Type configure terminal and press Enter Setting Up the New Users LoginInvalid Characters Value Ascii Hex Translation Local console disabled by conflict Telnet AccessDetermining the Current Access Level Determining the Available CommandsExiting from the System Using the List CommandChanging the System Identity Manually Logging Out If you are accessing the DSL router ThenAutomatically Logging Out Overview of DSL Router Configuration Configuring the DSL RouterInterfaces for the DSL Router Ethernet and DSL Interface Identifiers Service Domain IP Address AssignmentsUnnumbered DSL Interface Numbered DSL InterfaceSimplified Network Topology Network Considerations IP RoutingProxy ARP Address Resolution Protocol ARPBasic NAT Network Address Translation NATNetwork Address Port Translation Napt IP Options Processing Dynamic Host Configuration Protocol Dhcp ServerApplications Supported by NAT Dhcp Relay Agent IP Filtering SecurityLand Bug/Smurf Attack Prevention Routed vs. Bridged PDUs Routed Network Model Standard modeConfiguration Examples DSL Router Configuration ExamplesCustomer Premises CP Basic Configuration ExampleNAT Mapping Public IP Addresses Private IP Addresses Basic NAT Configuration ExampleNapt Mapping Public IP Addresses Private IP Addresses Napt Configuration ExampleCore Router 155.1.3.253 Console Port Connection Dhcp Relay with Proxy ARP Configuration Example Public IP Addresses for Basic NAT Private IP Addresses Dhcp Server with Basic NAT Configuration ExampleDownstream Router Configuration Example Monitoring the DSL Router Detecting ProblemsWhat to Monitor ± Ethernet Link up down Status of InterfacesShow interface Show interface eth1 dsl1Show statistics Interface StatisticsShow statistics eth1 dsl1 ip Discard Reasons for the Ethernet Interface eth1 1 Clearing StatisticsList of Discard Reasons Clear statistics eth1 dsl1 ipDiscard Reasons for the DSL Interface dsl1 1 Discard Reasons for the Ethernet Interface eth1 2Discard Reasons for IP Discard Reasons for the DSL Interface dsl1 2Show alarms Diagnostics and TroubleshootingDiagnostics and Troubleshooting Overview Alarms InquirySyslog ip ip-addr Syslog enable disableSystem Log Show syslogSyslog Messages 1 Level Description Event Syslog EventsSyslog level level Show log numberSyslog Messages 2 Level Description Event Syslog Message DisplayReporting Ping reply x.x.x.x Request Timed OUT PingPing Test Results Ping reply x.x.x.x bytes of data=nnTraceRoute Test Results TraceRouteX.x Command Line Interface Feature Command Line InterfaceNavigation Command RecallDocument Conventions Ethernet Frame Format Command Line Interface CommandsConfiguration Control Commands RFC 1483 EncapsulationInterface and Service Domain IP Address Delete eth1ifn dsl1ifn IP Routing TableIp route create dest-ipdest-mask next-hop-ip remote Ip route purge Proxy ARP ARP TableNat basic address ip-addrip-mask Nat basic enableNat napt enable Nat timeout timeNat napt delete udp tcp port Nat basic delete private-ipNat purge Nat disableDhcp server enable disable Dhcp ServerDhcp Relay Agent IP Packet Processing IP multicast enable disableIP processing enable disable Trap disable enable name of trapShow config Show Command OutputsNAT disabled or NAT enabled basic NAT Napt Show arp Show arp timeoutNAT timeout xx minutes NAT basic mappings Show ip route ip-addressShow traps Show NAT naptShow dhcp server Sample show dhcp relay display Show alarms Show syslog Show log #Show Dhcp relay Show interface Show statisticsConfiguration Default Settings Configuration Defaults Command Line ShortcutsCustomer ParadyneAbc123 BytesTable B-2. Command Line Input Shortcuts 1 Command Line Input ShortcutsTable B-2. Command Line Input Shortcuts 2 Show interface dsl1 eth1 Table B-2. Command Line Input Shortcuts 3Configuration Defaults & Command Line Shortcuts Snmp Overview Traps & MIBsTraps Overview Variable Binding DSL Router TrapsSystem Group MIBs OverviewStandard MIBs MIB II RFCSystem Ssssssssssss Boot bb.bb.bb 2nd Boot xx.xx.xx DSPYy.yy.yy H/W Releasezzz CCA part numberº Interfaces Group RFCInterfaces IfEntryIfOperStatus Specifies the current DSL interface Extension to Interfaces Table RFC Table C-5. IP Group Objects 1 Description Setting/ContentsIP Group RFC IP Cidr Route Group RFC Table C-5. IP Group Objects 2 Description Setting/ContentsIpCidrRouteEntry 11 ± Transmission GroupEthernet-Like MIB RFC Snmp GroupActive1 Paradyne Enterprise MIBsDevice Control MIB NoOp1Device Diagnostics MIB Traceroute ApplpingTestEntryApplTracerouteResultsEntry ConfigureAppTracerouteResultsEntry DevStatus1 Health and Status MIBDevStatus Factory1-to-active8 Configuration MIBSecondary Interface Configuration MIBPdnInetIpAddressTableEntry PrimaryDhcp MIB DSL Endpoint MIB Syslog MIB DSL Router Terminal Emulation Accessing the List Command OutputDSL Router Terminal Emulation Terminal Emulation Programs Numbers IndexIN-2 IN-3