Paradyne SMD2000-24T EMI Notices, Acta Customer Information, United States EMI Notice

Page 27

EMI Notices

United States – EMI Notice

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

The authority to operate this equipment is conditioned by the requirements that no modifications will be made to the equipment unless the changes or modifications are expressly approved by Paradyne Corporation.

If the equipment includes a ferrite choke or chokes, they must be installed as described in the installation instructions.

Canada – EMI Notice

This Class A digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.

ACTA Customer Information

This equipment complies with Part 68 of the FCC rules and the requirements adopted by the Administrative Council for Terminal Attachments (ACTA). On the bottom of the network extender is a label that contains, among other information, a product identifier in the format US:AAAEQ##TXXXX. If requested, this number must be provided to the telephone company.

The T1 network connections should be made using a Universal Service Order Code (USOC) type RJ48C jack. The Service Order Code 6.0F should be specified to the telephone company when ordering the T1 line. In addition, the proper Facility Interface Code must be specified to the Telephone Company. The network extender can be configured to support any of the following framing format and line signaling techniques. The network extender's configuration must correspond to the T1 line's parameters.

Facility Interface Codes

Code Description

 

 

 

04DU9-BN

1.544

Mbps superframe format (SF) without line power

 

 

 

04DU9-DN

1.544

Mbps SF and B8ZS without line power

 

 

 

04DU9-1KN

1.544

Mbps ANSI ESF without line power

 

 

 

04DU9-1SN

1.544

Mbps ANSI ESF and B8ZS without line power

 

 

 

27

Image 27
Contents SMD2000-24T 24-Port Shdsl Mini Dslam ContentsSoftware and Firmware License Agreement Product Documentation Online Site Selection Criteria Unpacking and Inspecting the EquipmentProcedure Installing Uplink Interface Modules OptionalUIM Side View Standoffs Tabletop Installation Rack Installation Powering Up the SMD2000-24T Negative Batt Lead Connecting the Shdsl RJ21 Cable Loop Bonded Shdsl Connection Connecting to the Remote Shdsl ModemsSingle Line Shdsl Connection Verifying the ConnectionsConnecting the Uplink Lines Shdsl Defaults Parameter Default SettingsShdsl Parameter Defaults T1 Uplink Parameter DefaultsUsername and Password Defaults Username/Passwords Access System and Management DefaultsUser Access Defaults System and Management Defaults ParameterMemory SMD2000-24T BackupBackup Criteria Data Needed for Backup Example Data StorageTemplate Criteria Data Needed for Backup Example SMD2000-24T TemplateShdsl Port Template Reset Button System ResetSystem Clear LEDs 1 State Indication Additional Information LED IndicatorsLNK LEDs 2 State Indication Additional InformationShdsl LEDs 3 State Indication Additional InformationShdsl RJ21 Pinouts Connector Pins Port Ring, Tip Pin AssignmentsShdsl RJ21 Pinouts T1 RJ48C Pin Assignments Function 10/100BaseT RJ45 PinoutsT1 RJ48C Pin Assignments Ethernet RJ45 Connection PinDB9 to 8-Pin Modular Adapter Pinouts SMD2000-24T Technical Specifications Criteria Technical SpecificationsCanada EMI Notice EMI NoticesActa Customer Information United States EMI NoticeCE Marking Class a ITE Japan NoticeImportant Safety Instructions Warranty, Sales, Service, and Training Information SMD2-A2-GN11-00