Quatech SSP-300, SSP-200 user manual Isr

Page 21

4.Open the Properties dialog for the SSP-200/300 device, then click the Resources tab to view the Input/Output Range and Interrupt Request resource allocations.

5.Several predefined Basic Configurations have been included for the SSP-200/300 (see Figure 5. SSP-200/300 Basic Configuration Table). The Basic Configurations provide many combinations of the operating modes and options listed below. See the Hardware Information section of this manual for complete descriptions.

?RS-422/485 output drivers enable option: The SSP-200/300’s ports may be configured for either full duplex or half duplex operation with this option. The default setting is the RS-422/485 ports are configured for full duplex operation with the RS-422/485 output drivers always enabled. In half duplex mode, the RS-422/485 transmitter may be enabled and disabled via the RTS (request to send) or DTR (data terminal ready) signals, or set to enable only when data is being transmitted (auto-toggle). Both RTS and DTR are controlled through the Modem Control Register of the 16750.

When the Use Automatic Settings check box is enabled Windows 95/98/ME will attempt to configure the SSP-200/300 in the order listed in the Basic Configurations table.

 

Basic

Auxiliary

I/O Range***

RS-422/485

Clock

Scratch

 

Configuration

Connections**

 

Output Drivers

Speed

Pad/ ISR

 

0000*

Loopback

3F8-3FF

Always Enabled

Normal

ISR

 

0001*

Loopback

2F8-2FF

Always Enabled

Normal

ISR

 

0002*

Loopback

3E8-3EF

Always Enabled

Normal

ISR

 

0003*

Loopback

2E8-2EF

Always Enabled

Normal

ISR

 

0004

Loopback

Any

Always Enabled

Normal

ISR

 

0005

Loopback

Any

Always Enabled

8x

ISR

 

0006

Loopback

Any

Auto Toggle

Normal

ISR

 

0007

Loopback

Any

RTS Controlled

Normal

ISR

 

0008

Loopback

Any

DTR Controlled

Normal

ISR

 

0009

Handshaking

Any

Always Enabled

Normal

ISR

 

000A

Clocking

Any

Always Enabled

Normal

ISR

 

000B

Loopback

Any

Auto Toggle

8x

ISR

 

000C

Loopback

Any

RTS Controlled

8x

ISR

 

000D

Loopback

Any

DTR Controlled

8x

ISR

 

000E

Handshaking

Any

Always Enabled

8x

ISR

 

000F

Clocking

Any

Always Enabled

8x

ISR

 

0010

Handshaking

Any

Auto Toggle

Normal

ISR

 

0011

Clocking

Any

Auto Toggle

Normal

ISR

 

0012

Handshaking

Any

RTS Controlled

Normal

ISR

 

0013

Clocking

Any

RTS Controlled

Normal

ISR

 

0014

Handshaking

Any

DTR Controlled

Normal

ISR

 

 

 

 

 

 

 

 

Windows 95/98/Millennium (ME)

3-3

Page 20 Page 22
Image 21
Page 20 Page 22
Contents SSP-200/300 SSP-200/300 Warranty InformationStandards to which Declaration of ConformityTable of Contents Introduction This page intentionally left blank DOS/Windows SSP-200/300 Client Driver for DOS Client Driver InstallationBaddress Command Line OptionsDevice = C\SSP-200\ SSP231CL.SYS Page Generic Client Drivers Common ProblemsMultiple Configuration Attempts SSP-200/300 Enabler for DOSOlder Versions of Card and Socket Services Available ResourcesR option is not used Page Page Card and Socket Services Software Memory Range ExclusionSocket Numbers Page Installing a SSP-200/300 Under Windows 95/98/ME SSP-200/300 Resource Settings in Windows 95/98/MEWindows 95/98/Millennium ME 2Changing Resource Settings with Device Manager 1Viewing Resource Settings with Device ManagerStart the Windows 95/98/ME Device Manager PC CardISR Auxout Frequently Asked Questions Basic Configuration List Not AvailableBase I/O Address Resource Modification Not Allowed This page intentionally left blank Windows Installing a SSP-200/300 Under WindowsDouble click ‘Serial Port Adapters’ Double click ‘Drivers’ Page Manager SSP-200/300 Resource Settings in WindowsLPT Viewing Resource Settings with Device Manager Changing Resource Settings with Device Manager Page Data Rate Multiplier Page Page Basic Auxiliary Range RS-422/485 Clock Scratch 0012 Loopback Any RTS Controlled Auxout Windows NT Installing SSP-200/300Page Page Page Auxiliary Channel Configuration Hardware InformationAuxiliary Channel RTS-CTS Handshaking Auxiliary Channel Handshaking Disabled Options Half Duplex OperationPage Recommended Termination Resistor Values Termination ResistorsThis page intentionally left blank SSP-200/300 Adapter Cable External ConnectionsThis page intentionally left blank Specifications SSP-200/300
Top Page Image Contents