Quatech DSCLP/SSCLP-100 user manual Address Map and Special Registers, Windows Configurations

Page 5

Table of Contents

1 General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

2 Hardware Configuration . . . . . . . . . . . . . . . . . . . . . . . . .

2.1 Factory Default Configuration . . . . . . . . . . . . . . . . . . . . . . .

2.2 Enable Scratchpad Register (SPAD, J2) . . . . . . . . . . . . . .

2.3 Force High-Speed UART Clock (X2 or X4, J4-J5) . . . .

9

9

9

10

3 Hardware Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

4 Address Map and Special Registers . . . . . . . . . . .

4.1 Base Address and Interrupt Level (IRQ) . . . . . . . . . . . . .

4.2 Enabling the Special Registers . . . . . . . . . . . . . . . . . . . . . .

4.3 Interrupt Status Register . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.4 Options Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.4.1 Enhanced Serial Adapter Identification . . . . . . . . . . .

4.4.2 Clock Rate Multiplier . . . . . . . . . . . . . . . . . . . . . . . . . . . .

13

13

14

14

15

15

16

5 Windows Configurations

 

. . . . . . . . . . . . . . . . . . . . . . .

. 17

5.1 Windows Millennium

. 17

5.2 Windows 2000

. 18

5.3 Windows 98

. 19

5.4 Windows 95

. 20

5.5 Using the "New Hardware Found" Wizard

. 20

5.6 Viewing Resources with Device Manager

. 21

5.6.1 Changing Resource Settings with Device Manager

. 24

6 Other Operating Systems . . . . . . . . . . . . . . . . . . . . . . .

6.1 Windows NT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6.2 OS/2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6.3 DOS and other operating systems . . . . . . . . . . . . . . . . . . .

6.3.1 QTPCI.EXE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

31

31

31

31

32

7 External Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

8 PCI Resource Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

9 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

10 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

5

DSCLP/SSCLP-100 User's Manual

Image 5
Contents DSCLP/SSCLP-100 Warranty Information Page Declaration of Conformity Address Map and Special Registers Windows ConfigurationsBase Address and Interrupt Level IRQ Enhanced Serial Adapter IdentificationGeneral Information Enable Scratchpad Register SPAD, J2 Hardware ConfigurationFactory Default Configuration Clock multiplier jumper options Jumper/connector locations Hardware InstallationPort Address Range Interrupt Status Register Enabling the Special RegistersBit Name Description Options RegisterRR1 RR0 Clock Rate MultiplierWindows Millennium Windows Windows Windows Using the New Hardware Found Wizard Page Viewing Resources with Device Manager Page Page Dual-Port RS-232 Serial Adapter Page Page For legacy applicattions which cannot Page Page Windows NT Other Operating SystemsOS/2 DOS and other operating systemsQTPCI.EXE QTPCI.EXE Expert Mode display External Connections RS-232 Port Signal SSCLP-100 PCI Resource MapICL3245CA SpecificationsPage Computer will not boot up TroubleshootingDSCLP/SSCLP-100