Patton electronic 2616RC user manual Cable installation, Connecting the Ethernet ports

Page 22

Model 2616RC T-DAC User Manual

2 • Hardware installation

 

 

Cable installation

This section describes installing the network interface cables.

Connecting the Ethernet ports

The T-DAC has a single 10/100 Ethernet interface for connection to your LAN (figure 5). The Ethernet port will autosense the correct speed of the local LAN and automatically negotiate half or full-duplex operation. This sec- tion describes connecting the T-DAC to the Ethernet LAN via an Ethernet hub, switch, or workstation.

Figure 5. Model 2616RC network and configuration ports

Connecting the 10/100Base-T Ethernet port to an Ethernet switch or hub

The 10/100Base-T Ethernet port (see figure 5) is designed to connect to an Ethernet switch or hub. The Ethernet RJ-45 pin and signal definitions for the T-DAC or for a NIC card in a workstation/PC are shown in figure 6 on page 23. Connect a straight-through CAT-5 cable (one wired as shown in figure 6) between the T-DAC and the hub/switch.

Cable installation

22

Page 21 Page 23
Image 22
Page 21 Page 23
Contents T1/E1 TDM-Digital Access Concentrator T-DAC Patton Electronics Company, Inc Summary Table of Contents Contents Operation and shutdown Compliance information List of Figures Model 2960 RAS Getting Started Guide List of Tables Audience About this guideStructure Precautions Safety when working with electricityGeneral conventions Typographical conventions used in this documentMouse conventions Chapter contents IntroductionModel 2616RC T1/E1 T-DAC overview Model 2616RC T-DACHardware overview WANPhysical dimensions Power systemTemperature Management servicesMIB LED display LEDHardware installation Introduction DAC blades installationUnpacking the Model 2616RC T-DAC Alignment/ESD pin and card handle Cable installation Connecting the Ethernet portsDB-9-to-RJ-45 cable diagram Connecting the T1/E1 WAN ports Pin Scsi to 8 RJ-45 connectors cableWAN cable‘s 68-pin Scsi connector Pin Scsi to open end cable SCSI-to-open-end WAN cableWAN cable’s 68 non-terminated twisted-pairs Installing the WAN cable to a punch-down block Punch-down block wiringPin Scsi to open end, 6 foot cable 10-3096TM68-6-Obsolete Pin Scsi to 64-pin female Telco 10-3096TM68/64-6Completing the hardware installation Configuring the T-DAC for operation Configuration prerequisites Initial configuration through the RS-232 control port Connecting the DB9-RJ45 adapter with the included cableSetting up the HyperTerminal or similar program session Connection Description windowConfigure your COM port settings as shown in , then click OK Login window Using a browser to complete Model 2616RC configuration Ethernet configuration windowDisplaying the T-DAC 2616RC web administration pages Home page overviewHome page window panes Configuring the default gateway FlashConfiguring the system clocking parameters ExampleSystem Clocking Configuration page, example For Clock Reference select secondary2 or slave3 Configuring the DS0 mapping DS0 Mapping Overview windowExamples for configuring static connections Configuring line settings and signaling for E1 Accessing the Line Interface SettingsConfiguring the E1 line interface settings T1/E1 Link Activity Ports 1 4From the Line Build Out pull-down menu select e1pulse1 Configuring line settings and signaling for T1 E1 Alarms Present indicatorConfiguring the T1 line settings Line Type pull-down menu with dsx1ESF2 selectedFrom the Line Build Out pull-down menu select t1pulse0dB1 Enabling/disabling the alarm card Alarm Card Information windowSaving your configuration Backing up your configuration parametersIMPORT/EXPORT Backing up the configuration store in flash memory Completing the installation Configuring the T-DAC for operation Operation and shutdown Activating the Model 2616RC De-activating the Model 2616RCTroubleshooting and maintenance Cited in De-activating the Model 2616RC on Fault analysis PowerSystem T1/E1 port test modes DSX1 payload loop dsx1PayloadLoopDSX1 line loop dsxLineLoop Line LoopExporting the current Model 2616RC configuration Periodic maintenanceMaintenance CalibrationMaintenance Troubleshooting and maintenance Removing the defective Model 2616RC Installing the replacement Model 2616RC Importing a saved configurationCompleting the installation Contacting Patton for assistance Contact information Warranty coverageOut-of-warranty service Returns for creditRMA numbers Return for credit policyShipping instructions Appendix a Compliance information EMCRadio and TV Interference SafetyCompliance Industry Canada NoticeCE Declaration of Conformity FCC Part 68 Acta StatementAuthorized European Representative Introduction Not Used Introduction
Related manuals
Manual 2 pages 12.27 Kb
Top Page Image Contents