Patton electronic 2616RC RS-232 control port, Power system, Central processing unit, Temperature

Page 16

Model 2616RC T-DAC User Manual

1 • Introduction

 

 

10Base-T half-/full-duplex operation (10 + 10)

Auto detection and fallback

10/100 Mbps link and status indicators

RS-232 control port

The RS-232 port provides for initial configuration of the Model 2616RC. The RS-232 port supports:

Asynchronous data rates of 19.2 kbps, 8 data bits, no parity, 1 stop bit.

An RJ-45 connector with EIA-561 pinouts

A management interface that supports VT-100 terminals

Hardware flow control (RTS and CTS)

Power system

The 2616RC obtains power from the Patton ForeFront chassis. Total power consumption is a maximum of 43 watts provided by modular power supplies installed in the Patton ForeFront chassis.

Central processing unit

The 2616RC employs an Intel i960VH RISC processor operating at 100 MHz/100 Mips. The CPU controls the memory, front/back-panel and management interface for WAN time slot mapping, local switching, loop- back and the management system. The memory holds:

4 MB Flash ROM

8 MB EDO DRAM

System timing

The T1/E1 T-DAC’s system timing may be derived from an internal clock from an on-board chip, external BITS clock, or a network clock from one of the T1/E1 WAN ports or from the ForeFront system chassis clock. The clock source may be configured in primary, secondary, or slave mode.

The system timing is configured through the NMS.

Temperature

Operating range: 32–122°F (0–50°C)

Altitude

Maximum operating altitude: 15,000 feet (4,752 meters)

Humidity

5 to 95% relative humidity (RH), non-condensing

Physical dimensions

1.75 inches (4.44 cm) height, standard 19-inch (48.26 cm) width, 12-inch (30.48 cm) depth

Management services

Out-of-Band RS-232 configuration port for management and control

Hardware overview

16

Image 16
Contents T1/E1 TDM-Digital Access Concentrator T-DAC Patton Electronics Company, Inc Summary Table of Contents Contents Operation and shutdown Compliance information List of Figures Model 2960 RAS Getting Started Guide List of Tables Audience About this guideStructure Precautions Safety when working with electricityGeneral conventions Typographical conventions used in this documentMouse conventions Chapter contents IntroductionModel 2616RC T1/E1 T-DAC overview Model 2616RC T-DACHardware overview WANPower system TemperaturePhysical dimensions Management servicesMIB LED display LEDHardware installation Introduction DAC blades installationUnpacking the Model 2616RC T-DAC Alignment/ESD pin and card handle Cable installation Connecting the Ethernet portsDB-9-to-RJ-45 cable diagram Connecting the T1/E1 WAN ports Pin Scsi to 8 RJ-45 connectors cableWAN cable‘s 68-pin Scsi connector Pin Scsi to open end cable SCSI-to-open-end WAN cableWAN cable’s 68 non-terminated twisted-pairs Installing the WAN cable to a punch-down block Punch-down block wiringPin Scsi to open end, 6 foot cable 10-3096TM68-6-Obsolete Pin Scsi to 64-pin female Telco 10-3096TM68/64-6Completing the hardware installation Configuring the T-DAC for operation Configuration prerequisites Initial configuration through the RS-232 control port Connecting the DB9-RJ45 adapter with the included cableSetting up the HyperTerminal or similar program session Connection Description windowConfigure your COM port settings as shown in , then click OK Login window Using a browser to complete Model 2616RC configuration Ethernet configuration windowDisplaying the T-DAC 2616RC web administration pages Home page overviewHome page window panes Configuring the default gateway FlashConfiguring the system clocking parameters ExampleSystem Clocking Configuration page, example For Clock Reference select secondary2 or slave3 Configuring the DS0 mapping DS0 Mapping Overview windowExamples for configuring static connections Configuring line settings and signaling for E1 Accessing the Line Interface SettingsConfiguring the E1 line interface settings T1/E1 Link Activity Ports 1 4From the Line Build Out pull-down menu select e1pulse1 Configuring line settings and signaling for T1 E1 Alarms Present indicatorConfiguring the T1 line settings Line Type pull-down menu with dsx1ESF2 selectedFrom the Line Build Out pull-down menu select t1pulse0dB1 Enabling/disabling the alarm card Alarm Card Information windowSaving your configuration Backing up your configuration parametersIMPORT/EXPORT Backing up the configuration store in flash memory Completing the installation Configuring the T-DAC for operation Operation and shutdown Activating the Model 2616RC De-activating the Model 2616RCTroubleshooting and maintenance Cited in De-activating the Model 2616RC on Fault analysis PowerSystem T1/E1 port test modes DSX1 payload loop dsx1PayloadLoopDSX1 line loop dsxLineLoop Line LoopPeriodic maintenance MaintenanceExporting the current Model 2616RC configuration CalibrationMaintenance Troubleshooting and maintenance Removing the defective Model 2616RC Installing the replacement Model 2616RC Importing a saved configurationCompleting the installation Contacting Patton for assistance Warranty coverage Out-of-warranty serviceContact information Returns for creditRMA numbers Return for credit policyShipping instructions Appendix a Compliance information EMCSafety ComplianceRadio and TV Interference Industry Canada NoticeCE Declaration of Conformity FCC Part 68 Acta StatementAuthorized European Representative Introduction Not Used Introduction
Related manuals
Manual 2 pages 12.27 Kb