Patton electronic 2616RC user manual Completing the hardware installation

Page 30

Model 2616RC T-DAC User Manual	2 • Hardware installation

Completing the hardware installation

This section verifies that the T-DAC hardware is operational to the point where you can begin configuring the software settings.

Power is delivered from the Patton ForeFront chassis backplane through the 47-pin PICMG 2.11 power con- nectors on the 2616RC blades. Upon insertion into the Patton ForeFront chassis, the Model 2616RC immedi- ately powers up and begins its boot cycle. During the boot cycle the following should occur:

1.The POWER LED illuminates, indicating normal power is being applied to the 2616RC.

2.The green SYSTEM LED begins flashing, indicating the 2616RC is operating normally.

Hardware installation is now complete. To configure the 2616RC for operation, refer to chapter 3, “Configur- ing the T-DAC for operation” on page 31.

Completing the hardware installation

30

Image 30

Contents T1/E1 TDM-Digital Access Concentrator T-DAC Patton Electronics Company, Inc Summary Table of Contents Contents Operation and shutdown Compliance information List of Figures Model 2960 RAS Getting Started Guide List of Tables About this guide AudienceStructure Precautions Safety when working with electricityTypographical conventions used in this document General conventionsMouse conventions Chapter contents IntroductionModel 2616RC T1/E1 T-DAC overview Model 2616RC T-DACHardware overview WANPhysical dimensions Power systemTemperature Management servicesMIB LED display LEDHardware installation DAC blades installation IntroductionUnpacking the Model 2616RC T-DAC Alignment/ESD pin and card handle Cable installation Connecting the Ethernet portsDB-9-to-RJ-45 cable diagram Connecting the T1/E1 WAN ports Pin Scsi to 8 RJ-45 connectors cableWAN cable‘s 68-pin Scsi connector Pin Scsi to open end cable SCSI-to-open-end WAN cableWAN cable’s 68 non-terminated twisted-pairs Installing the WAN cable to a punch-down block Punch-down block wiringPin Scsi to open end, 6 foot cable 10-3096TM68-6-Obsolete Pin Scsi to 64-pin female Telco 10-3096TM68/64-6Completing the hardware installation Configuring the T-DAC for operation Configuration prerequisites Initial configuration through the RS-232 control port Connecting the DB9-RJ45 adapter with the included cableSetting up the HyperTerminal or similar program session Connection Description windowConfigure your COM port settings as shown in , then click OK Login window Using a browser to complete Model 2616RC configuration Ethernet configuration windowDisplaying the T-DAC 2616RC web administration pages Home page overviewHome page window panes Configuring the default gateway FlashConfiguring the system clocking parameters ExampleSystem Clocking Configuration page, example For Clock Reference select secondary2 or slave3 Configuring the DS0 mapping DS0 Mapping Overview windowExamples for configuring static connections Configuring line settings and signaling for E1 Accessing the Line Interface SettingsConfiguring the E1 line interface settings T1/E1 Link Activity Ports 1 4From the Line Build Out pull-down menu select e1pulse1 Configuring line settings and signaling for T1 E1 Alarms Present indicatorConfiguring the T1 line settings Line Type pull-down menu with dsx1ESF2 selectedFrom the Line Build Out pull-down menu select t1pulse0dB1 Enabling/disabling the alarm card Alarm Card Information windowSaving your configuration Backing up your configuration parametersIMPORT/EXPORT Backing up the configuration store in flash memory Completing the installation Configuring the T-DAC for operation Operation and shutdown Activating the Model 2616RC De-activating the Model 2616RCTroubleshooting and maintenance Cited in De-activating the Model 2616RC on Fault analysis PowerSystem T1/E1 port test modes DSX1 payload loop dsx1PayloadLoopDSX1 line loop dsxLineLoop Line LoopExporting the current Model 2616RC configuration Periodic maintenanceMaintenance CalibrationMaintenance Troubleshooting and maintenance Removing the defective Model 2616RC Installing the replacement Model 2616RC Importing a saved configurationCompleting the installation Contacting Patton for assistance Contact information Warranty coverageOut-of-warranty service Returns for creditReturn for credit policy RMA numbersShipping instructions Appendix a Compliance information EMCRadio and TV Interference SafetyCompliance Industry Canada NoticeFCC Part 68 Acta Statement CE Declaration of ConformityAuthorized European Representative Introduction Not Used Introduction

Related manuals

Manual 2 pages 12.27 Kb