Patton electronic 2616RC user manual FCC Part 68 Acta Statement, CE Declaration of Conformity

Page 77

Model 2616RC T-DAC User Manual

A • Compliance information

 

 

designated by the supplier. Any repairs or alterations made by the user to this equipment, or equipment mal- functions, may give the telecommunications company cause to request the user to disconnect the equipment. Users should ensure for their own protection that the ground connections of the power utility, telephone lines and internal metallic water pipe system, are connected together. This protection may be particularly important in rural areas.

FCC Part 68 (ACTA) Statement

This equipment complies with Part 68 of FCC rules and the requirements adopted by ACTA. On the bottom side of this equipment is a label that contains—among other information—a product identifier in the format US: AAAEQ##TXXXX. If requested, this number must be provided to the telephone company.

The method used to connect this equipment to the premises wiring and telephone network must comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA.

If this equipment causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of service may be required. But if advance notice isn’t practical, the telephone company will notify the customer as soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you believe it is necessary.

The telephone company may make changes in its facilities, equipment, operations or procedures that could affect the operation of the equipment. If this happens the telephone company will provide advance notice in order for you to make necessary modifications to maintain uninterrupted service.

If trouble is experienced with this equipment, for repair or warranty information, please contact our company. If the equipment is causing harm to the telephone network, the telephone company may request that you dis- connect the equipment until the problem is resolved.

Connection to party line service is subject to state tariffs. Contact the state public utility commission, public service commission or corporation commission for information.

CE Declaration of Conformity

We certify that the apparatus identified in this document conforms to the requirements of Council Directive 1999/5/EC on the approximation of the laws of the member states relating to Radio and Telecommunication Terminal Equipment and the mutual recognition of their conformity.

The safety advice in the documentation accompanying this product shall be obeyed. The conformity to the above directive is indicated by the CE sign on the device.

Authorized European Representative

D R M Green

European Compliance Services Limited.

Oakdene House, Oak Road

Watchfield, Swindon, Wilts SN6 8TD, UK

FCC Part 68 (ACTA) Statement

77

Image 77
Contents T1/E1 TDM-Digital Access Concentrator T-DAC Patton Electronics Company, Inc Summary Table of Contents Contents Operation and shutdown Compliance information List of Figures Model 2960 RAS Getting Started Guide List of Tables Structure About this guideAudience Safety when working with electricity PrecautionsMouse conventions Typographical conventions used in this documentGeneral conventions Introduction Chapter contentsModel 2616RC T-DAC Model 2616RC T1/E1 T-DAC overviewWAN Hardware overviewTemperature Power systemPhysical dimensions Management servicesMIB LED LED displayHardware installation Unpacking the Model 2616RC T-DAC DAC blades installationIntroduction Alignment/ESD pin and card handle Connecting the Ethernet ports Cable installationDB-9-to-RJ-45 cable diagram Pin Scsi to 8 RJ-45 connectors cable Connecting the T1/E1 WAN portsWAN cable‘s 68-pin Scsi connector SCSI-to-open-end WAN cable Pin Scsi to open end cableWAN cable’s 68 non-terminated twisted-pairs Punch-down block wiring Installing the WAN cable to a punch-down blockPin Scsi to 64-pin female Telco 10-3096TM68/64-6 Pin Scsi to open end, 6 foot cable 10-3096TM68-6-ObsoleteCompleting the hardware installation Configuring the T-DAC for operation Configuration prerequisites Connecting the DB9-RJ45 adapter with the included cable Initial configuration through the RS-232 control portConnection Description window Setting up the HyperTerminal or similar program sessionConfigure your COM port settings as shown in , then click OK Login window Ethernet configuration window Using a browser to complete Model 2616RC configurationHome page overview Displaying the T-DAC 2616RC web administration pagesHome page window panes Flash Configuring the default gatewayExample Configuring the system clocking parametersSystem Clocking Configuration page, example For Clock Reference select secondary2 or slave3 DS0 Mapping Overview window Configuring the DS0 mappingExamples for configuring static connections Accessing the Line Interface Settings Configuring line settings and signaling for E1T1/E1 Link Activity Ports 1 4 Configuring the E1 line interface settingsFrom the Line Build Out pull-down menu select e1pulse1 E1 Alarms Present indicator Configuring line settings and signaling for T1Line Type pull-down menu with dsx1ESF2 selected Configuring the T1 line settingsFrom the Line Build Out pull-down menu select t1pulse0dB1 Alarm Card Information window Enabling/disabling the alarm cardBacking up your configuration parameters Saving your configurationIMPORT/EXPORT Backing up the configuration store in flash memory Completing the installation Configuring the T-DAC for operation Operation and shutdown De-activating the Model 2616RC Activating the Model 2616RCTroubleshooting and maintenance Cited in De-activating the Model 2616RC on Power Fault analysisSystem DSX1 payload loop dsx1PayloadLoop T1/E1 port test modesLine Loop DSX1 line loop dsxLineLoopMaintenance Periodic maintenanceExporting the current Model 2616RC configuration CalibrationMaintenance Troubleshooting and maintenance Removing the defective Model 2616RC Importing a saved configuration Installing the replacement Model 2616RCCompleting the installation Contacting Patton for assistance Out-of-warranty service Warranty coverageContact information Returns for creditShipping instructions Return for credit policyRMA numbers EMC Appendix a Compliance informationCompliance SafetyRadio and TV Interference Industry Canada NoticeAuthorized European Representative FCC Part 68 Acta StatementCE Declaration of Conformity Introduction Not Used Introduction
Related manuals
Manual 2 pages 12.27 Kb