Patton electronic 2616RC Enabling/disabling the alarm card, Alarm Card Information window

Page 52

Model 2616RC T-DAC User Manual

3 • Configuring the T-DAC for operation

 

 

Enabling/disabling the alarm card

The Alarm Card window (see figure 49) is where you can configure the alarm card polling mode to determine whether the 2616RC monitors the alarm card status for the chassis.

1.Click on Alarm Card under the configuration menu to display the Alarm Card Information window.

2.From the Alarm Card Polling Mode menu, select an option from the drop-down menu to enable/disable the alarm card.

doNotMonitor(0)—Disables the alarm card

monitorAlarmCard(1)—Enables the alarm card

3.Click Submit to save the change.

Note If the chassis contains more than one (2616RC/3096RC/3196RC) or any combination thereof, then only one card should be enabled to monitor the alarm card.

Figure 49. Alarm Card Information window

Using a browser to complete Model 2616RC configuration

52

Image 52
Contents T1/E1 TDM-Digital Access Concentrator T-DAC Patton Electronics Company, Inc Summary Table of Contents Contents Operation and shutdown Compliance information List of Figures Model 2960 RAS Getting Started Guide List of Tables Audience About this guideStructure Precautions Safety when working with electricityGeneral conventions Typographical conventions used in this documentMouse conventions Chapter contents IntroductionModel 2616RC T1/E1 T-DAC overview Model 2616RC T-DACHardware overview WANPower system TemperaturePhysical dimensions Management servicesMIB LED display LEDHardware installation Introduction DAC blades installationUnpacking the Model 2616RC T-DAC Alignment/ESD pin and card handle Cable installation Connecting the Ethernet portsDB-9-to-RJ-45 cable diagram Connecting the T1/E1 WAN ports Pin Scsi to 8 RJ-45 connectors cableWAN cable‘s 68-pin Scsi connector Pin Scsi to open end cable SCSI-to-open-end WAN cableWAN cable’s 68 non-terminated twisted-pairs Installing the WAN cable to a punch-down block Punch-down block wiringPin Scsi to open end, 6 foot cable 10-3096TM68-6-Obsolete Pin Scsi to 64-pin female Telco 10-3096TM68/64-6Completing the hardware installation Configuring the T-DAC for operation Configuration prerequisites Initial configuration through the RS-232 control port Connecting the DB9-RJ45 adapter with the included cableSetting up the HyperTerminal or similar program session Connection Description windowConfigure your COM port settings as shown in , then click OK Login window Using a browser to complete Model 2616RC configuration Ethernet configuration windowDisplaying the T-DAC 2616RC web administration pages Home page overviewHome page window panes Configuring the default gateway FlashConfiguring the system clocking parameters ExampleSystem Clocking Configuration page, example For Clock Reference select secondary2 or slave3 Configuring the DS0 mapping DS0 Mapping Overview windowExamples for configuring static connections Configuring line settings and signaling for E1 Accessing the Line Interface SettingsConfiguring the E1 line interface settings T1/E1 Link Activity Ports 1 4From the Line Build Out pull-down menu select e1pulse1 Configuring line settings and signaling for T1 E1 Alarms Present indicatorConfiguring the T1 line settings Line Type pull-down menu with dsx1ESF2 selectedFrom the Line Build Out pull-down menu select t1pulse0dB1 Enabling/disabling the alarm card Alarm Card Information windowSaving your configuration Backing up your configuration parametersIMPORT/EXPORT Backing up the configuration store in flash memory Completing the installation Configuring the T-DAC for operation Operation and shutdown Activating the Model 2616RC De-activating the Model 2616RCTroubleshooting and maintenance Cited in De-activating the Model 2616RC on Fault analysis PowerSystem T1/E1 port test modes DSX1 payload loop dsx1PayloadLoopDSX1 line loop dsxLineLoop Line LoopPeriodic maintenance MaintenanceExporting the current Model 2616RC configuration CalibrationMaintenance Troubleshooting and maintenance Removing the defective Model 2616RC Installing the replacement Model 2616RC Importing a saved configurationCompleting the installation Contacting Patton for assistance Warranty coverage Out-of-warranty serviceContact information Returns for creditRMA numbers Return for credit policyShipping instructions Appendix a Compliance information EMCSafety ComplianceRadio and TV Interference Industry Canada NoticeCE Declaration of Conformity FCC Part 68 Acta StatementAuthorized European Representative Introduction Not Used Introduction
Related manuals
Manual 2 pages 12.27 Kb