Patton electronic 1063, 07MOS10xx-GS Gaining Access to the System, Access through the Serial Port

Page 43

OnSite Series Getting Started Guide	4 • System Management Access

Gaining Access to the System

There are two ways of gaining access to the system management functions. One way is through the SERIAL port and the command line interface (CLI). The other way is through the Ethernet LAN port and the web browser interface. The following sections describe the procedures for each of the access methods.

Access through the Serial Port

To gain management access to the system for the ﬁrst time through the SERIAL port, follow these steps:

1.Connect a PC to the SERIAL management port.

Note Use the DB-9-to-RJ-45 adapter cable supplied with the system.

2.Launch the VT100 terminal emulation program on the PC.

Note Conﬁgure the terminal in accordance with the settings in Table 14.

3.Press the Enter key on the PC to obtain a login prompt from the system.

4.Log in to the system using the Super user ID and password.

Note Only the Super user is able to perform the following task.

Note The user ID for the Super user is super (all lowercase letters).

Note The factory-assigned default password for the Super user is super (all lowercase letters).

After successful completion of the login, the system responds with the CLI (command-line interface) prompt.

Note The CLI command prompt for the system is OnSite >

5.Type the following CLI command to conﬁgure the IP address for the Ethernet LAN management port, and then press the Enter key:

config mgmt-enet ip-address aaa.bbb.ccc.ddd

Note aaa.bbb.ccc.ddd is the standard dotted-decimal notation.

6.Type the following CLI command to conﬁgure the net mask for the Ethernet LAN management port, and then press the Enter key:

config mgmt-enet ip-netmask aaa.bbb.ccc.ddd

7.Type the following CLI command to conﬁgure the default gateway for the Ethernet LANmanagement port, and then press the Enter key:

config mgmt-enet default-gateway aaa.bbb.ccc.ddd

Note By default, the IP address is set to 192.168.2.100, the net mask is set to 255.255.255.0, and the default gateway is set to 192.168.2.1

Gaining Access to the System

43

Image 43

Contents Metro-Optical Transport Access Nodes Mailsupport@patton.com Summary Table of Contents Table of Contents System Management Access Terms and Acronyms List of Figures List of Tables Audience About this guideStructure PrecautionsGeneral conventions Typographical conventions used in this documentMouse conventions Power Cable Safety when using electricityFiber-Optic Ports Optical SafetyFiber-Optic Safety Precautions Electrostatic Discharge DamageProduct Overview Chapter contentsOnSite Platforms IntroductionSDH Trunks OS1052 Base System Application Overview Typical OS1052 application OS1052 ApplicationOS1052 Map + Modules Typical OS1063 application OS1063 ApplicationOS1063 Map + Modules Installation Overview Site Preparation Unpacking and InspectionPlanning Your Site Site EnvironmentSite Requirements Operating Environment Requirements Power Supply Requirements Securing the Rack Mechanical Recommendations for the RackProtective Grounding for the Rack and Chassis Space Requirements for the RackOnSite System Installation Tools and Equipment for Installation and MaintenanceMounting the Chassis to an EIA/TIA 19-Inch Rack Mounting the OS-10 System Chassis in an EIA/TIA 19-Inch Rack Mounting the Chassis to an Etsi RackMounting the OS-10 System in an Etsi 300-mm Rack Mounting the OS-10 System Chassis on a Wall Mounting the Chassis on the WallConnecting Power to the OS-10 System Installing the Chassis Ground ConnectionConnecting AC Power to the OS-10 System Powering On the OS-10 System with AC Power Wiring the OS-10 System for DC Power Installation Overview Checking the OS-10 System Installation System Management Access General Overview Detail of the Management Ports Ethernet LAN Management PortSerial Management Port Provides the pin assignments for the RJ-45 connectorAccess through the Serial Port Gaining Access to the SystemAccess through the Ethernet LAN Management Port Launching the GUI Application Web-Based Management InterfaceGUI Frames Provides Conﬁguring an Snmp Trap Receiver Autonomous Alarm MessagesConﬁguring an Authorized OnSight NMS Server Location of EOW port AUX 1 on OS-10 Series Chassis Engineering Orderwire EOWSystem Management Access Conﬁguring the Engineering Orderwire EOW Function System Management Access Contacting Patton for assistance Contact information Warranty coverageRMA numbers Return for credit policyAppendix a Compliance information FCC Part 68 Acta Statement SafetyCompliance Radio and TV InterferenceAuthorized European Representative Declaration of ConformityAppendix B Speciﬁcations Model OS1052 Operations DimensionsWeight PowerModel OS1063 Operations Appendix C Terms and Acronyms Abbreviation Meaning AbbreviationsLcas TDM