Patton electronic 1063 Compliance, Radio and TV Interference, FCC Part 68 Acta Statement, Safety

Page 57

OnSite Series Getting Started Guide

A • Compliance information

 

 

Compliance

The compliance information in this document is incomplete and subject to change.

IMPORTANT

EMC

EN 55022 Class A

FCC part 15 Class A

Safety

EN 60950

UL 60950

Radio and TV Interference

The OnSite OS-10 Series generates and uses radio frequency energy, and if not installed and used properly-that is, in strict accordance with the manufacturer’s instructions-may cause interference to radio and television reception. The OnSite OS-10 Series have been tested and found to comply with the limits for a Class A com- puting device in accordance with specifications in Subpart B of Part 15 of FCC rules, which are designed to provide reasonable protection from such interference in a commercial installation. However, there is no guar- antee that interference will not occur in a particular installation. If the OnSite OS-10 Series does cause inter- ference to radio or television reception, which can be determined by disconnecting the unit, the user is encouraged to try to correct the interference by one or more of the following measures: moving the computing equipment away from the receiver, re-orienting the receiving antenna and/or plugging the receiving equipment into a different AC outlet (such that the computing equipment and receiver are on different branches).

FCC Part 68 (ACTA) Statement

This equipment complies with Part 68 of FCC rules and the requirements adopted by ACTA. On the bottom side of this equipment is a label that contains—among other information—a product identifier in the format US: AAAEQ##TXXXX. If requested, this number must be provided to the telephone company.

The method used to connect this equipment to the premises wiring and telephone network must comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA.

If this equipment causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of service may be required. But if advance notice isn’t practical, the telephone company will notify the customer as soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you believe it is necessary.

The telephone company may make changes in its facilities, equipment, operations or procedures that could affect the operation of the equipment. If this happens the telephone company will provide advance notice in order for you to make necessary modifications to maintain uninterrupted service.

Compliance

57

Image 57
Contents Metro-Optical Transport Access Nodes Mailsupport@patton.com Summary Table of Contents Table of Contents System Management Access Terms and Acronyms List of Figures List of Tables Audience About this guideStructure PrecautionsTypographical conventions used in this document General conventionsMouse conventions Power Cable Safety when using electricityFiber-Optic Safety Precautions Optical SafetyElectrostatic Discharge Damage Fiber-Optic PortsProduct Overview Chapter contentsOnSite Platforms IntroductionSDH Trunks OS1052 Base System Application Overview Typical OS1052 application OS1052 ApplicationOS1052 Map + Modules Typical OS1063 application OS1063 ApplicationOS1063 Map + Modules Installation Overview Site Preparation Unpacking and InspectionSite Environment Planning Your SiteSite Requirements Operating Environment Requirements Power Supply Requirements Protective Grounding for the Rack and Chassis Mechanical Recommendations for the RackSpace Requirements for the Rack Securing the RackTools and Equipment for Installation and Maintenance OnSite System InstallationMounting the Chassis to an EIA/TIA 19-Inch Rack Mounting the OS-10 System Chassis in an EIA/TIA 19-Inch Rack Mounting the Chassis to an Etsi RackMounting the OS-10 System in an Etsi 300-mm Rack Mounting the OS-10 System Chassis on a Wall Mounting the Chassis on the WallConnecting Power to the OS-10 System Installing the Chassis Ground ConnectionConnecting AC Power to the OS-10 System Powering On the OS-10 System with AC Power Wiring the OS-10 System for DC Power Installation Overview Checking the OS-10 System Installation System Management Access General Overview Detail of the Management Ports Ethernet LAN Management PortSerial Management Port Provides the pin assignments for the RJ-45 connectorAccess through the Serial Port Gaining Access to the SystemAccess through the Ethernet LAN Management Port Launching the GUI Application Web-Based Management InterfaceGUI Frames Provides Configuring an Snmp Trap Receiver Autonomous Alarm MessagesConfiguring an Authorized OnSight NMS Server Location of EOW port AUX 1 on OS-10 Series Chassis Engineering Orderwire EOWSystem Management Access Configuring the Engineering Orderwire EOW Function System Management Access Contacting Patton for assistance Contact information Warranty coverageRMA numbers Return for credit policyAppendix a Compliance information Compliance SafetyRadio and TV Interference FCC Part 68 Acta StatementAuthorized European Representative Declaration of ConformityAppendix B Specifications Model OS1052 Weight DimensionsPower OperationsModel OS1063 Operations Appendix C Terms and Acronyms Abbreviation Meaning AbbreviationsLcas TDM