Patton electronic 07MOS10xx-GS manual Model OS1063

Page 62

OnSite Series Getting Started Guide	B • Specifications

Model OS1063

Trunk Interfaces

STM-1: G.707, G.783

Optics: G.957 S-1.1, L-1.1 and L-1.2 options

Client Interfaces

E1: G.703, 75-ohm and 120-ohm options

T1: G.703, 100-ohm

Ethernet 10/100Base-TX: 802.3u

Expansion Modules

SDH: STM-1 optical (2 ports) • STM-1 electrical (2 ports)

PDH: E1 (21 ports) • E3/DS3 (3 ports)

Packet Data: 10/100Base-TX (8 ports)

Conﬁguration & Port Capacity for 2 Expansion Slots

STM-1:Base: 2 • Max: 6

E1: Base: 21 • Max: 63

E3/DS3: Base: – • Max: 6

10/100Base-TX:Base: – • Max: 18

Protection

Linear MSP 1+1 • SNCP/I and SNCP/N

Bandwidth Connectivity and Provisioning

Connectivity: VC-12, VC-3 levels

One-way, two-way, drop-and-continue and multicast connections

VCAT: VC-12-Xv and VC-3-Xv

LCAS: G.7042

Packet encapsulation: GFP-F (G.7041)

Timing & Synchronization

Internal: Stratum 3 clock

Line timing: STM-1 and E1/T1

External timing: Dual Sync In/Out ports at 2 or 1.5 Mbps/MHz

SSM support: G.781

System Access

Serial RS-232 and Ethernet LAN management ports

IP over DCCr and DCCm options

IP over E1 signal mapped into selected VC-12 channel

DCC transparency (any subset of DCC rows)

Telnet

Model OS1063

62

Image 62

Contents Metro-Optical Transport Access Nodes Mailsupport@patton.com Summary Table of Contents Table of Contents System Management Access Terms and Acronyms List of Figures List of Tables About this guide AudiencePrecautions StructureMouse conventions Typographical conventions used in this documentGeneral conventions Safety when using electricity Power CableElectrostatic Discharge Damage Optical SafetyFiber-Optic Safety Precautions Fiber-Optic PortsChapter contents Product OverviewIntroduction OnSite PlatformsSDH Trunks OS1052 Base System Application Overview OS1052 Application Typical OS1052 applicationOS1052 Map + Modules OS1063 Application Typical OS1063 applicationOS1063 Map + Modules Installation Overview Unpacking and Inspection Site PreparationSite Requirements Site EnvironmentPlanning Your Site Operating Environment Requirements Power Supply Requirements Space Requirements for the Rack Mechanical Recommendations for the RackProtective Grounding for the Rack and Chassis Securing the RackMounting the Chassis to an EIA/TIA 19-Inch Rack Tools and Equipment for Installation and MaintenanceOnSite System Installation Mounting the Chassis to an Etsi Rack Mounting the OS-10 System Chassis in an EIA/TIA 19-Inch RackMounting the OS-10 System in an Etsi 300-mm Rack Mounting the Chassis on the Wall Mounting the OS-10 System Chassis on a WallInstalling the Chassis Ground Connection Connecting Power to the OS-10 SystemConnecting AC Power to the OS-10 System Powering On the OS-10 System with AC Power Wiring the OS-10 System for DC Power Installation Overview Checking the OS-10 System Installation System Management Access General Overview Ethernet LAN Management Port Detail of the Management PortsProvides the pin assignments for the RJ-45 connector Serial Management PortGaining Access to the System Access through the Serial PortAccess through the Ethernet LAN Management Port Web-Based Management Interface Launching the GUI ApplicationGUI Frames Provides Autonomous Alarm Messages Conﬁguring an Snmp Trap ReceiverConﬁguring an Authorized OnSight NMS Server Engineering Orderwire EOW Location of EOW port AUX 1 on OS-10 Series ChassisSystem Management Access Conﬁguring the Engineering Orderwire EOW Function System Management Access Contacting Patton for assistance Warranty coverage Contact informationReturn for credit policy RMA numbersAppendix a Compliance information Radio and TV Interference SafetyCompliance FCC Part 68 Acta StatementDeclaration of Conformity Authorized European RepresentativeAppendix B Speciﬁcations Model OS1052 Power DimensionsWeight OperationsModel OS1063 Operations Appendix C Terms and Acronyms Abbreviations Abbreviation MeaningLcas TDM