TP-Link TL-WDN4800 manual 450Mbps Wireless N Dual Band PCI Express Adapter

Page 17
¾Wireless Mode - Here displays the wireless mode.

TL-WDN4800

450Mbps Wireless N Dual Band PCI Express Adapter

Figure 3-1

The following table describes the items found on the Current Status screen.

¾Profile Name - This shows the name of current selected configuration profile. The configuration of Profile name will be described on the General tab of Profile Management.

¾Link Status - This shows whether the station is associated to the wireless network.

¾Wireless Mode - Here displays the wireless mode.

¾Network Type - The type of network and the station currently connected are shown here. The options include:

Infrastructure (access point)

Ad Hoc

)Note:

You can configure the network type and wireless mode on the Advanced tab of Profile Management.

¾IP Address - This displays the computer’s IP address.

¾Control Channel - This shows the currently connected channel.

¾Data Encryption - Here displays the encryption type the driver is using. You can configure it on the Security tab of Profile Management.

¾Server Based Authentication - This shows whether the server based authentication is used.

11

Image 17
Contents Rev 1.1.0 TL-WDN4800 450Mbps Wireless N Dual Band PCI Express AdapterCOPYRIGHT & TRADEMARKS FCC RF Radiation Exposure Statement FCC STATEMENTNational restrictions CE Mark WarningCountry RestrictionShenzhen, P. R. China DECLARATION OF CONFORMITYCONTENTS 450Mbps Wireless N Dual Band PCI Express Adapter Package ContentsConventions 1.1 Overview of the product 1.2 FeaturesChapter 1. Introduction The driver has not been installed 1.3 LED StatusThe driver has been installed but there is no data being transmitted Flashing Slowly2.2 Software Installation Chapter 2. Installation Guide2.1 Hardware Installation 2. Click Install Driver&Utility to load the following screen TL-WDN4800 5. Click Browse to change the destination location for the software, or you can leave it default then click Next in the screen below shown in Figure 8. Wait a while for the setup as shown in Figure TL-WDN4800 3.1 For Windows XP Chapter 3. Configuration Guide¾ Wireless Mode - Here displays the wireless mode 3.1.2 Profile Management ¾ Profile Name - Please enter the Profile name which identifies the configuration profile. This name must be unique. Note that the profile names are not case-sensitive ¾ WPA/WPA2 Passphrase Wi-Fi Protected Access Passphrase ¾ WPA/WPA2 Wi-Fi Protected Access¾ 802.1x Enables 802.1x security The WEP security mode is not available for 802.11n450Mbps Wireless N Dual Band PCI Express Adapter ¾ Network Type There are basically two modes of networking 1. Go to the Profile Management tab shown in Figure 3. Click Remove 2. Click Refresh to refresh the list at any time 4. Highlight a profile in the Auto Selected Profiles box 3.1.3 Diagnostics 3.2 For Windows Vista Icon means the connection has been established. Icon means there is no connection. To establish a connection, please follow the steps below 3.3 For Windows 1. Click the icon at the bottom of your screen in your system tray and then you will see the available wireless network list. Select the SSID of your Access Point and click Connect TL-WDN4800 Chapter 4. QSS Configuration 4.1 PBC Push Button Configuration method TL-WDN4800 1 Enter a PIN into your AP device 2 Enter the PIN from your AP device 4.2 PIN methodThere are two ways to configure the QSS by PIN method 4.2.1 Enter a PIN into your AP device 4.2.2 Enter the PIN from your AP device Appendix A Specifications Appendix B Glossary scale, or when it is necessary to connect the wired and wireless networks
Related manuals
Manual 2 pages 27.54 Kb Manual 47 pages 28.13 Kb Manual 53 pages 17.51 Kb