TP-Link TL-WDN4800 Appendix A Specifications, 450Mbps Wireless N Dual Band PCI Express Adapter

Page 39

Appendix A: Specifications

TL-WDN4800

450Mbps Wireless N Dual Band PCI Express Adapter

Appendix A: Specifications

Normal

	Interface	PCI Express Interface

	Standards	IEEE802.11a; IEEE802.11b; IEEE802.11g; IEEE802.11n

	Operating System	Windows XP / Windows Vista / Windows 7

	Radio Data Rate	11a: 6/9/12/18/24/36/48/54Mbps
		11b: 1/2/5.5/11Mbps
		11g: 6/9/12/18/24/36/48/54Mbps
		11n: Up to 450Mbps

		11a: OFDM
	Modulation	11b: CCK, QPSK, BPSK;
	Modulation	11g: OFDM;
		11g: OFDM;
		11n: QPSK, BPSK, 16-QAM, 64-QAM

	Media Access Protocol	CSMA/CA with ACK

	Data Security	WPA/WPA2; 64/128-bit WEP; TKIP/AES

	Frequency	2.4 ~ 2.4835GHz, 5.180 ~ 5.240GHz, 5.745 ~ 5.825GHz

	Spread Spectrum	Direct Sequence Spread Spectrum (DSSS)

	Safety & Emissions	FCC, CE


	Environmental and Physical

	Operating Temp.	0℃ ~ 40℃ (32℉~104℉)

	Storage Temp.	-40℃~ 70℃ (-40℉~158℉)

	Working Humidity	10% ~ 90% RH, Non-condensing

	Storage Humidity	5% ~ 90% RH, Non-condensing

33

Image 39

Contents Rev 1.1.0 TL-WDN4800 450Mbps Wireless N Dual Band PCI Express AdapterCOPYRIGHT & TRADEMARKS FCC RF Radiation Exposure Statement FCC STATEMENTRestriction CE Mark WarningNational restrictions CountryShenzhen, P. R. China DECLARATION OF CONFORMITYCONTENTS Package Contents Conventions450Mbps Wireless N Dual Band PCI Express Adapter 1.2 Features Chapter 1. Introduction1.1 Overview of the product Flashing Slowly 1.3 LED StatusThe driver has not been installed The driver has been installed but there is no data being transmittedChapter 2. Installation Guide 2.1 Hardware Installation2.2 Software Installation 2. Click Install Driver&Utility to load the following screen TL-WDN4800 5. Click Browse to change the destination location for the software, or you can leave it default then click Next in the screen below shown in Figure 8. Wait a while for the setup as shown in Figure TL-WDN4800 3.1 For Windows XP Chapter 3. Configuration Guide¾ Wireless Mode - Here displays the wireless mode 3.1.2 Profile Management ¾ Profile Name - Please enter the Profile name which identifies the configuration profile. This name must be unique. Note that the profile names are not case-sensitive The WEP security mode is not available for 802.11n ¾ WPA/WPA2 Wi-Fi Protected Access¾ WPA/WPA2 Passphrase Wi-Fi Protected Access Passphrase ¾ 802.1x Enables 802.1x security450Mbps Wireless N Dual Band PCI Express Adapter ¾ Network Type There are basically two modes of networking 1. Go to the Profile Management tab shown in Figure 3. Click Remove 2. Click Refresh to refresh the list at any time 4. Highlight a profile in the Auto Selected Profiles box 3.1.3 Diagnostics 3.2 For Windows Vista Icon means the connection has been established. Icon means there is no connection. To establish a connection, please follow the steps below 3.3 For Windows 1. Click the icon at the bottom of your screen in your system tray and then you will see the available wireless network list. Select the SSID of your Access Point and click Connect TL-WDN4800 Chapter 4. QSS Configuration 4.1 PBC Push Button Configuration method TL-WDN4800 4.2 PIN method There are two ways to configure the QSS by PIN method1 Enter a PIN into your AP device 2 Enter the PIN from your AP device 4.2.1 Enter a PIN into your AP device 4.2.2 Enter the PIN from your AP device Appendix A Specifications Appendix B Glossary scale, or when it is necessary to connect the wired and wireless networks

Related manuals

Manual 2 pages 27.54 Kb

Manual 47 pages 28.13 Kb

Manual 53 pages 17.51 Kb