TP-Link TL-WDN4800 CE Mark Warning, National restrictions, Country, Restriction, Reason/remark

Page 4
CE Mark Warning

CE Mark Warning

This is a class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.

National restrictions

This device is intended for home and office use in all EU countries (and other countries following the EU directive 1999/5/EC) without any limitation except for the countries mentioned below:

Country

Restriction

Reason/remark

 

 

 

Bulgaria

None

General authorization required for outdoor use and

public service

 

 

 

 

 

Outdoor use limited to 10

FrancemW e.i.r.p. within the band 2454-2483.5 MHz

Military Radiolocation use. Refarming of the 2.4 GHz band has been ongoing in recent years to allow current relaxed regulation. Full implementation planned 2012

Italy

None

If used outside of own premises, general authorization is

required

 

 

 

 

 

Luxembourg

None

General authorization required for network and service

supply(not for spectrum)

 

 

 

 

 

Norway

Implemented

This subsection does not apply for the geographical area

within a radius of 20 km from the centre of Ny-Ålesund

 

 

 

 

 

Russian Federation

None

Only for indoor applications

 

 

 

Note: Please don’t use the product outdoors in France.

Image 4
Contents TL-WDN4800 450Mbps Wireless N Dual Band PCI Express Adapter Rev 1.1.0COPYRIGHT & TRADEMARKS FCC STATEMENT FCC RF Radiation Exposure StatementCE Mark Warning National restrictionsCountry RestrictionDECLARATION OF CONFORMITY Shenzhen, P. R. ChinaCONTENTS Conventions Package Contents450Mbps Wireless N Dual Band PCI Express Adapter Chapter 1. Introduction 1.2 Features1.1 Overview of the product 1.3 LED Status The driver has not been installedThe driver has been installed but there is no data being transmitted Flashing Slowly2.1 Hardware Installation Chapter 2. Installation Guide2.2 Software Installation 2. Click Install Driver&Utility to load the following screen 450Mbps Wireless N Dual Band PCI Express Adapter 5. Click Browse to change the destination location for the software, or you can leave it default then click Next in the screen below shown in Figure 8. Wait a while for the setup as shown in Figure 450Mbps Wireless N Dual Band PCI Express Adapter Chapter 3. Configuration Guide 3.1 For Windows XP¾ Wireless Mode - Here displays the wireless mode 3.1.2 Profile Management ¾ Profile Name - Please enter the Profile name which identifies the configuration profile. This name must be unique. Note that the profile names are not case-sensitive ¾ WPA/WPA2 Wi-Fi Protected Access ¾ WPA/WPA2 Passphrase Wi-Fi Protected Access Passphrase¾ 802.1x Enables 802.1x security The WEP security mode is not available for 802.11n450Mbps Wireless N Dual Band PCI Express Adapter ¾ Network Type There are basically two modes of networking 1. Go to the Profile Management tab shown in Figure 3. Click Remove 2. Click Refresh to refresh the list at any time 4. Highlight a profile in the Auto Selected Profiles box 3.1.3 Diagnostics 3.2 For Windows Vista Icon means the connection has been established. Icon means there is no connection. To establish a connection, please follow the steps below 3.3 For Windows 1. Click the icon at the bottom of your screen in your system tray and then you will see the available wireless network list. Select the SSID of your Access Point and click Connect 450Mbps Wireless N Dual Band PCI Express Adapter Chapter 4. QSS Configuration 4.1 PBC Push Button Configuration method 450Mbps Wireless N Dual Band PCI Express Adapter There are two ways to configure the QSS by PIN method 4.2 PIN method1 Enter a PIN into your AP device 2 Enter the PIN from your AP device 4.2.1 Enter a PIN into your AP device 4.2.2 Enter the PIN from your AP device Appendix A Specifications Appendix B Glossary scale, or when it is necessary to connect the wired and wireless networks
Related manuals
Manual 2 pages 27.54 Kb Manual 47 pages 28.13 Kb Manual 53 pages 17.51 Kb