TP-Link TL-WDN4800 manual Introduction, Overview of the product, Features

Page 8

TL-WDN4800

450Mbps Wireless N Dual Band PCI Express Adapter

Chapter 1. Introduction

1.1Overview of the product

The adapter is designed to provide a high-speed and unrivaled wireless performance for your notebook and PC. With a faster wireless connection, you can get a better Internet experience, such as downloading, gaming, video streaming and so on.

The TL-WDN4800’s auto-sensing capability allows high packet transfer rate of up to 450Mbps for maximum throughput. It has good capability on anti-jamming; it can also interoperate with other wireless (802.11a/b/g/n) products. The adapter supports WEP, WPA and WPA2 encryption to prevent outside intrusion and protect your personal information from being exposed.

The Quick Setup Wizard guides you step-by-step through the installation process; the TP-LINK Wireless Configuration Utility helps you create a wireless connection immediately.

With unmatched wireless performance, reception, and security protection, the TL-WDN4800 is the best choice for easily adding or upgrading wireless connectivity.

1.2Features

¾IEEE802.11a, IEEE802.11b, IEEE802.11g, IEEE802.11n standards

¾Supports WPA/WPA2 data security, IEEE802.1x authentication, TKIP/AES encryption, WEP encryption

¾Make use of IEEE 802.11n wireless technology to provide a wireless data rate of up to 450Mbps

¾supports automatically adjust to lower speeds due to distance or other operating limitations

¾Provides PCI Express interface

¾Supports Ad-Hoc and Infrastructure modes

¾Good capability on anti-jamming

¾Supports roaming between access points when configured in Infrastructure mode

¾Ease to configure and provides monitoring information

¾Supports Windows XP, Windows Vista and Windows 7

2

Image 8

Contents TL-WDN4800 450Mbps Wireless N Dual Band PCI Express Adapter Rev 1.1.0COPYRIGHT & TRADEMARKS FCC STATEMENT FCC RF Radiation Exposure StatementCE Mark Warning National restrictionsCountry RestrictionDECLARATION OF CONFORMITY Shenzhen, P. R. ChinaCONTENTS 450Mbps Wireless N Dual Band PCI Express Adapter Package ContentsConventions 1.1 Overview of the product 1.2 FeaturesChapter 1. Introduction 1.3 LED Status The driver has not been installedThe driver has been installed but there is no data being transmitted Flashing Slowly2.2 Software Installation Chapter 2. Installation Guide2.1 Hardware Installation 2. Click Install Driver&Utility to load the following screen 450Mbps Wireless N Dual Band PCI Express Adapter 5. Click Browse to change the destination location for the software, or you can leave it default then click Next in the screen below shown in Figure 8. Wait a while for the setup as shown in Figure 450Mbps Wireless N Dual Band PCI Express Adapter Chapter 3. Configuration Guide 3.1 For Windows XP¾ Wireless Mode - Here displays the wireless mode 3.1.2 Profile Management ¾ Profile Name - Please enter the Profile name which identifies the configuration profile. This name must be unique. Note that the profile names are not case-sensitive ¾ WPA/WPA2 Wi-Fi Protected Access ¾ WPA/WPA2 Passphrase Wi-Fi Protected Access Passphrase¾ 802.1x Enables 802.1x security The WEP security mode is not available for 802.11n450Mbps Wireless N Dual Band PCI Express Adapter ¾ Network Type There are basically two modes of networking 1. Go to the Profile Management tab shown in Figure 3. Click Remove 2. Click Refresh to refresh the list at any time 4. Highlight a profile in the Auto Selected Profiles box 3.1.3 Diagnostics 3.2 For Windows Vista Icon means the connection has been established. Icon means there is no connection. To establish a connection, please follow the steps below 3.3 For Windows 1. Click the icon at the bottom of your screen in your system tray and then you will see the available wireless network list. Select the SSID of your Access Point and click Connect 450Mbps Wireless N Dual Band PCI Express Adapter Chapter 4. QSS Configuration 4.1 PBC Push Button Configuration method 450Mbps Wireless N Dual Band PCI Express Adapter 1 Enter a PIN into your AP device 2 Enter the PIN from your AP device 4.2 PIN methodThere are two ways to configure the QSS by PIN method 4.2.1 Enter a PIN into your AP device 4.2.2 Enter the PIN from your AP device Appendix A Specifications Appendix B Glossary scale, or when it is necessary to connect the wired and wireless networks

Related manuals

Manual 2 pages 27.54 Kb

Manual 47 pages 28.13 Kb

Manual 53 pages 17.51 Kb