TP-Link TL-WDN4800 manual Fcc Statement, FCC RF Radiation Exposure Statement

Page 3

FCC STATEMENT

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and receiver.

•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

•Consult the dealer or an experienced radio/ TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1)This device may not cause harmful interference.

2)This device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not Expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

FCC RF Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment has been SAR-evaluated for use in hand. SAR measurements are based on a 4mm spacing from the body and that compliance is achieved at that distance.

Image 3

Contents Rev 1.1.0 TL-WDN4800 450Mbps Wireless N Dual Band PCI Express AdapterCOPYRIGHT & TRADEMARKS FCC RF Radiation Exposure Statement FCC STATEMENTRestriction CE Mark WarningNational restrictions CountryShenzhen, P. R. China DECLARATION OF CONFORMITYCONTENTS Package Contents Conventions450Mbps Wireless N Dual Band PCI Express Adapter 1.2 Features Chapter 1. Introduction1.1 Overview of the product Flashing Slowly 1.3 LED StatusThe driver has not been installed The driver has been installed but there is no data being transmittedChapter 2. Installation Guide 2.1 Hardware Installation2.2 Software Installation 2. Click Install Driver&Utility to load the following screen TL-WDN4800 5. Click Browse to change the destination location for the software, or you can leave it default then click Next in the screen below shown in Figure 8. Wait a while for the setup as shown in Figure TL-WDN4800 3.1 For Windows XP Chapter 3. Configuration Guide¾ Wireless Mode - Here displays the wireless mode 3.1.2 Profile Management ¾ Profile Name - Please enter the Profile name which identifies the configuration profile. This name must be unique. Note that the profile names are not case-sensitive The WEP security mode is not available for 802.11n ¾ WPA/WPA2 Wi-Fi Protected Access¾ WPA/WPA2 Passphrase Wi-Fi Protected Access Passphrase ¾ 802.1x Enables 802.1x security450Mbps Wireless N Dual Band PCI Express Adapter ¾ Network Type There are basically two modes of networking 1. Go to the Profile Management tab shown in Figure 3. Click Remove 2. Click Refresh to refresh the list at any time 4. Highlight a profile in the Auto Selected Profiles box 3.1.3 Diagnostics 3.2 For Windows Vista Icon means the connection has been established. Icon means there is no connection. To establish a connection, please follow the steps below 3.3 For Windows 1. Click the icon at the bottom of your screen in your system tray and then you will see the available wireless network list. Select the SSID of your Access Point and click Connect TL-WDN4800 Chapter 4. QSS Configuration 4.1 PBC Push Button Configuration method TL-WDN4800 4.2 PIN method There are two ways to configure the QSS by PIN method1 Enter a PIN into your AP device 2 Enter the PIN from your AP device 4.2.1 Enter a PIN into your AP device 4.2.2 Enter the PIN from your AP device Appendix A Specifications Appendix B Glossary scale, or when it is necessary to connect the wired and wireless networks

Related manuals

Manual 2 pages 27.54 Kb

Manual 47 pages 28.13 Kb

Manual 53 pages 17.51 Kb