TP-Link TL-WDN4800 manual Diagnostics, 450Mbps Wireless N Dual Band PCI Express Adapter

Page 27

3.1.3Diagnostics

TL-WDN4800

450Mbps Wireless N Dual Band PCI Express Adapter

network. If the connection fails, the client adapter will try the next highest priority profile that matches the SSID until an available network is found.

3.1.3Diagnostics

The Diagnostics tab of the TP-LINK Wireless Configuration Utility (TWCU) provides buttons used to retrieve receiving and transmitting statistics. The Diagnostics tab does not require any configuration.

The Diagnostics tab lists the following receiving and transmitting diagnostics for frames received or transmitted by the wireless network adapter:

¾Multicast frames transmitted and received

¾Broadcast frames transmitted and received

¾Unicast frames transmitted and received

¾Total bytes transmitted and received

Figure 3-12

3.1.3.1. Check Driver Information

Click the Adapter Information button in the screen above, you will see the adapter information, including general information about the wireless network adapter and the Network Driver Interface Specification (NDIS) driver. Access the adapter information from the Diagnostics tab.

¾Card Name - The name of the wireless network adapter.

¾MAC Address - The MAC address of the wireless network adapter.

¾Driver - The driver name and path of the wireless network adapter driver.

21

Image 27

Contents Rev 1.1.0 TL-WDN4800 450Mbps Wireless N Dual Band PCI Express AdapterCOPYRIGHT & TRADEMARKS FCC RF Radiation Exposure Statement FCC STATEMENTRestriction CE Mark WarningNational restrictions CountryShenzhen, P. R. China DECLARATION OF CONFORMITYCONTENTS Package Contents Conventions450Mbps Wireless N Dual Band PCI Express Adapter 1.2 Features Chapter 1. Introduction1.1 Overview of the product Flashing Slowly 1.3 LED StatusThe driver has not been installed The driver has been installed but there is no data being transmittedChapter 2. Installation Guide 2.1 Hardware Installation2.2 Software Installation 2. Click Install Driver&Utility to load the following screen TL-WDN4800 5. Click Browse to change the destination location for the software, or you can leave it default then click Next in the screen below shown in Figure 8. Wait a while for the setup as shown in Figure TL-WDN4800 3.1 For Windows XP Chapter 3. Configuration Guide¾ Wireless Mode - Here displays the wireless mode 3.1.2 Profile Management ¾ Profile Name - Please enter the Profile name which identifies the configuration profile. This name must be unique. Note that the profile names are not case-sensitive The WEP security mode is not available for 802.11n ¾ WPA/WPA2 Wi-Fi Protected Access¾ WPA/WPA2 Passphrase Wi-Fi Protected Access Passphrase ¾ 802.1x Enables 802.1x security450Mbps Wireless N Dual Band PCI Express Adapter ¾ Network Type There are basically two modes of networking 1. Go to the Profile Management tab shown in Figure 3. Click Remove 2. Click Refresh to refresh the list at any time 4. Highlight a profile in the Auto Selected Profiles box 3.1.3 Diagnostics 3.2 For Windows Vista Icon means the connection has been established. Icon means there is no connection. To establish a connection, please follow the steps below 3.3 For Windows 1. Click the icon at the bottom of your screen in your system tray and then you will see the available wireless network list. Select the SSID of your Access Point and click Connect TL-WDN4800 Chapter 4. QSS Configuration 4.1 PBC Push Button Configuration method TL-WDN4800 4.2 PIN method There are two ways to configure the QSS by PIN method1 Enter a PIN into your AP device 2 Enter the PIN from your AP device 4.2.1 Enter a PIN into your AP device 4.2.2 Enter the PIN from your AP device Appendix A Specifications Appendix B Glossary scale, or when it is necessary to connect the wired and wireless networks

Related manuals

Manual 2 pages 27.54 Kb

Manual 47 pages 28.13 Kb

Manual 53 pages 17.51 Kb