TP-Link TL-WDN4800 manual Profile Management, 450Mbps Wireless N Dual Band PCI Express Adapter

Page 18

3.1.2Profile Management

TL-WDN4800

450Mbps Wireless N Dual Band PCI Express Adapter

¾Signal Strength - This shows the strength of the signal.

Click Advanced on the screen above, you can see advanced information about the program and its operations.

3.1.2Profile Management

Click the Profile Management tab of the TWCU and the next screen will appear (shown in Figure

3-2X). The Profile Management screen provides tools to:

¾Add a new profile

¾Modify a profile

¾Remove a profile

¾Activate a Profile

¾Import a Profile

¾Export a Profile

¾Scan Available Networks

¾Order profiles

Figure 3-2

3.1.2.1. Add or Modify a Configuration Profile

To add a new configuration profile, click New on the Profile Management tab. To modify a configuration profile, select the configuration profile from the Profile list and click Modify. Then you will see the Management dialog box (shown in Figure 3-3).

12

Image 18

Contents TL-WDN4800 450Mbps Wireless N Dual Band PCI Express Adapter Rev 1.1.0COPYRIGHT & TRADEMARKS FCC STATEMENT FCC RF Radiation Exposure StatementCountry CE Mark WarningNational restrictions RestrictionDECLARATION OF CONFORMITY Shenzhen, P. R. ChinaCONTENTS Package Contents Conventions450Mbps Wireless N Dual Band PCI Express Adapter 1.2 Features Chapter 1. Introduction1.1 Overview of the product The driver has been installed but there is no data being transmitted 1.3 LED StatusThe driver has not been installed Flashing SlowlyChapter 2. Installation Guide 2.1 Hardware Installation2.2 Software Installation 2. Click Install Driver&Utility to load the following screen 450Mbps Wireless N Dual Band PCI Express Adapter 5. Click Browse to change the destination location for the software, or you can leave it default then click Next in the screen below shown in Figure 8. Wait a while for the setup as shown in Figure 450Mbps Wireless N Dual Band PCI Express Adapter Chapter 3. Configuration Guide 3.1 For Windows XP¾ Wireless Mode - Here displays the wireless mode 3.1.2 Profile Management ¾ Profile Name - Please enter the Profile name which identifies the configuration profile. This name must be unique. Note that the profile names are not case-sensitive ¾ 802.1x Enables 802.1x security ¾ WPA/WPA2 Wi-Fi Protected Access¾ WPA/WPA2 Passphrase Wi-Fi Protected Access Passphrase The WEP security mode is not available for 802.11n450Mbps Wireless N Dual Band PCI Express Adapter ¾ Network Type There are basically two modes of networking 1. Go to the Profile Management tab shown in Figure 3. Click Remove 2. Click Refresh to refresh the list at any time 4. Highlight a profile in the Auto Selected Profiles box 3.1.3 Diagnostics 3.2 For Windows Vista Icon means the connection has been established. Icon means there is no connection. To establish a connection, please follow the steps below 3.3 For Windows 1. Click the icon at the bottom of your screen in your system tray and then you will see the available wireless network list. Select the SSID of your Access Point and click Connect 450Mbps Wireless N Dual Band PCI Express Adapter Chapter 4. QSS Configuration 4.1 PBC Push Button Configuration method 450Mbps Wireless N Dual Band PCI Express Adapter 4.2 PIN method There are two ways to configure the QSS by PIN method1 Enter a PIN into your AP device 2 Enter the PIN from your AP device 4.2.1 Enter a PIN into your AP device 4.2.2 Enter the PIN from your AP device Appendix A Specifications Appendix B Glossary scale, or when it is necessary to connect the wired and wireless networks

Related manuals

Manual 2 pages 27.54 Kb

Manual 47 pages 28.13 Kb

Manual 53 pages 17.51 Kb