TP-Link TL-WDN4800 manual QSS Configuration, 450Mbps Wireless N Dual Band PCI Express Adapter

Page 33
Chapter 4. QSS Configuration

TL-WDN4800

450Mbps Wireless N Dual Band PCI Express Adapter

Chapter 4. QSS Configuration

QSS (Quick Secure Setup) function allows you to add a new wireless device to an existing network quickly.

If the wireless router supports Wi-Fi Protected Setup (WPS), you can establish a wireless connection between wireless card and router using either Push Button Configuration (PBC) method or PIN method.

)Note:

QSS function is not supported in Windows 7 OS.

1.First, the QSS software should be installed. Insert the Resource CD into your CD-ROM drive, and the Figure 4-1will appear. To continue, select the TL-WDN4800.There will be a menu including: Install Driver&Utility, Install QSS and User Guide.

Figure 4-1

2.Next, select Install QSS to load the following screen.

27

Page 32 Page 34
Image 33
Page 32 Page 34
Contents Rev 1.1.0 TL-WDN4800 450Mbps Wireless N Dual Band PCI Express AdapterCOPYRIGHT & TRADEMARKS FCC RF Radiation Exposure Statement FCC STATEMENTNational restrictions CE Mark WarningCountry RestrictionShenzhen, P. R. China DECLARATION OF CONFORMITYCONTENTS Package Contents Conventions450Mbps Wireless N Dual Band PCI Express Adapter 1.2 Features Chapter 1. Introduction1.1 Overview of the product The driver has not been installed 1.3 LED StatusThe driver has been installed but there is no data being transmitted Flashing SlowlyChapter 2. Installation Guide 2.1 Hardware Installation2.2 Software Installation 2. Click Install Driver&Utility to load the following screen TL-WDN4800 5. Click Browse to change the destination location for the software, or you can leave it default then click Next in the screen below shown in Figure 8. Wait a while for the setup as shown in Figure TL-WDN4800 3.1 For Windows XP Chapter 3. Configuration Guide¾ Wireless Mode - Here displays the wireless mode 3.1.2 Profile Management ¾ Profile Name - Please enter the Profile name which identifies the configuration profile. This name must be unique. Note that the profile names are not case-sensitive ¾ WPA/WPA2 Passphrase Wi-Fi Protected Access Passphrase ¾ WPA/WPA2 Wi-Fi Protected Access¾ 802.1x Enables 802.1x security The WEP security mode is not available for 802.11n450Mbps Wireless N Dual Band PCI Express Adapter ¾ Network Type There are basically two modes of networking 1. Go to the Profile Management tab shown in Figure 3. Click Remove 2. Click Refresh to refresh the list at any time 4. Highlight a profile in the Auto Selected Profiles box 3.1.3 Diagnostics 3.2 For Windows Vista Icon means the connection has been established. Icon means there is no connection. To establish a connection, please follow the steps below 3.3 For Windows 1. Click the icon at the bottom of your screen in your system tray and then you will see the available wireless network list. Select the SSID of your Access Point and click Connect TL-WDN4800 Chapter 4. QSS Configuration 4.1 PBC Push Button Configuration method TL-WDN4800 4.2 PIN method There are two ways to configure the QSS by PIN method1 Enter a PIN into your AP device 2 Enter the PIN from your AP device 4.2.1 Enter a PIN into your AP device 4.2.2 Enter the PIN from your AP device Appendix A Specifications Appendix B Glossary scale, or when it is necessary to connect the wired and wireless networks
Related manuals
Manual 2 pages 27.54 Kb Manual 47 pages 28.13 Kb Manual 53 pages 17.51 Kb
Top Page Image Contents