TP-Link TL-WDN4800 manual Declaration Of Conformity, Shenzhen, P. R. China

Page 5

DECLARATION OF CONFORMITY

TP-LINK TECHNOLOGIES CO., LTD

DECLARATION OF CONFORMITY

For the following equipment:

Product Description: 450Mbps Wireless N Dual Band PCI Express Adapter

Model No.: TL-WDN4800

Trademark: TP-LINK

We declare under our own responsibility that the above products satisfy all the technical regulations applicable to the product within the scope of Council Directives:

Directives 1999/5/EC

The above product is in conformity with the following standards or other normative documents:

ETSI EN 300 328 V1.7.1: 2006

ETSI EN 301 489-1 V1.8.1:2008 & ETSI EN 301 489-17 V1.3.2:2008

EN60950-1:2006

EN62311:2008

Recommendation 1999/519/EC

Person is responsible for marking this declaration:

Yang Hongliang

Product Manager of International Business

TP-LINK TECHNOLOGIES CO., LTD.

South Building, No.5 Keyuan Road, Central Zone, Science & Technology Park, Nanshan,

Shenzhen, P. R. China

Image 5

Contents Rev 1.1.0 TL-WDN4800 450Mbps Wireless N Dual Band PCI Express AdapterCOPYRIGHT & TRADEMARKS FCC RF Radiation Exposure Statement FCC STATEMENTNational restrictions CE Mark WarningCountry RestrictionShenzhen, P. R. China DECLARATION OF CONFORMITYCONTENTS 450Mbps Wireless N Dual Band PCI Express Adapter Package ContentsConventions 1.1 Overview of the product 1.2 FeaturesChapter 1. Introduction The driver has not been installed 1.3 LED StatusThe driver has been installed but there is no data being transmitted Flashing Slowly2.2 Software Installation Chapter 2. Installation Guide2.1 Hardware Installation 2. Click Install Driver&Utility to load the following screen TL-WDN4800 5. Click Browse to change the destination location for the software, or you can leave it default then click Next in the screen below shown in Figure 8. Wait a while for the setup as shown in Figure TL-WDN4800 3.1 For Windows XP Chapter 3. Configuration Guide¾ Wireless Mode - Here displays the wireless mode 3.1.2 Profile Management ¾ Profile Name - Please enter the Profile name which identifies the configuration profile. This name must be unique. Note that the profile names are not case-sensitive ¾ WPA/WPA2 Passphrase Wi-Fi Protected Access Passphrase ¾ WPA/WPA2 Wi-Fi Protected Access¾ 802.1x Enables 802.1x security The WEP security mode is not available for 802.11n450Mbps Wireless N Dual Band PCI Express Adapter ¾ Network Type There are basically two modes of networking 1. Go to the Profile Management tab shown in Figure 3. Click Remove 2. Click Refresh to refresh the list at any time 4. Highlight a profile in the Auto Selected Profiles box 3.1.3 Diagnostics 3.2 For Windows Vista Icon means the connection has been established. Icon means there is no connection. To establish a connection, please follow the steps below 3.3 For Windows 1. Click the icon at the bottom of your screen in your system tray and then you will see the available wireless network list. Select the SSID of your Access Point and click Connect TL-WDN4800 Chapter 4. QSS Configuration 4.1 PBC Push Button Configuration method TL-WDN4800 1 Enter a PIN into your AP device 2 Enter the PIN from your AP device 4.2 PIN methodThere are two ways to configure the QSS by PIN method 4.2.1 Enter a PIN into your AP device 4.2.2 Enter the PIN from your AP device Appendix A Specifications Appendix B Glossary scale, or when it is necessary to connect the wired and wireless networks

Related manuals

Manual 2 pages 27.54 Kb

Manual 47 pages 28.13 Kb

Manual 53 pages 17.51 Kb