Polycom 3725-24004-001/A manual Controlling the Camera Manually, Setting and Using Camera Presets

Page 27

Using the Polycom PowerCam Presenter

Controlling the Camera Manually

If you do not want to use automatic camera tracking, you can manually pan, tilt, and zoom the camera. You can manually adjust the camera at any time: it does not matter whether the locator pack is powered on or powered off.

To control the camera manually:

1. Press Off Off on the remote control.

2.Manually adjust the camera by pressing Left, Right, Up,

Down, Zoom, Preset 1, or Preset 2.

Setting and Using Camera Presets

Camera presets are stored camera positions. Presets allow you to automatically point the camera at pre-defined locations in a room.

You can set up to two presets.

To set or change a camera preset:

1. If automatic camera tracking is enabled, disable it by pressing Off Off on the remote control.

2.Adjust the camera to the position to want:

— Press	Left,	Right,	Up, or	Down to move the
camera left, right, up, or down.

— Press Zoom In or Zoom Out to zoom the camera in or out.

3.Press and hold Preset 1 to store the camera’s position as Preset 1 or press and hold Preset 2 to store the camera’s position as Preset 2.

Hold the button for at least five seconds or, if you have your video output connected to connector on the Polycom Presenter controller, until the following icon appears on the screen:

Any preset that was already stored at Preset 1 or Preset 2 is updated to the new preset position.

2 - 15

Image 27

Contents VideoVoiceDataWeb License Terms Trademark InformationAbout this Guide User’s Guide for the Polycom PowerCam Presenter Contents Maintenance and Troubleshooting Introducing the Polycom PowerCam Presenter Name Component Description System ComponentsTilt, or zoom VSX Series , available at Setting up the Polycom PowerCam Presenter Key Features Ease of UseState-of-the-Art Technology Setting up the Hardware Using the Polycom PowerCam PresenterUsing the Remote Control Configuring User Settings Configuring Camera SettingsSetting Description Input Signal Backlight Compensation Setting Description Camera DirectionRestricted Unrestricted Not Specified Unrestricted Calibrating for Background Noise Calibrating the CameraConfiguring LAN Properties Configuring Video Output Settings Display messages Using Automatic Camera TrackingSetting Description Output On-screen Connected to connector On the controllerEnabling and Disabling Automatic Camera Tracking Setting and Using Presenter Views Using the Polycom PowerCam Presenter Enabling and Disabling Automatic Zooming Controlling the Camera Manually Setting and Using Camera PresetsObtaining System Information Tips on Using the Polycom PowerCam Presenter10’ 15’ 20’ 25’ 30’ 35’ 40’ 45’ 50’ 10’ 15’ 20’ 25’ 30’ 35’ 40’ 45’ 50’ Maintenance and Troubleshooting Maintaining the SystemCharging the Locator Pack Batteries Upgrading the Software Automatic Camera Tracking SpecificationsSpecification Description Troubleshooting the System Power and Hardware IssuesSymptom Problem Corrective Action To Composite Set the Input Signal to S-Video Set the Input Signal to CompositeCamera Movement Issues Left Right DownOff Automatic camera Camera inputs and outputs Set Screen Saver Wait Time to Off Go to System Admin Settings General SettingsSystem Settings Appearance Set to Restricted orContacting Technical Support User’s Guide for the Polycom PowerCam Presenter Charging Safety and Regulatory NoticesImportant Safeguards Safety Precautions for Lithium Ion Battery PacksSafety Warnings When Using the Battery Safety Warnings When Discharging the Battery License Restrictions Warranty InformationWarranty Information Regulatory Notices Part 15 FCC RulesIndustry Canada IC Safety and Regulatory Notices Regulatory Notices Special Safety Instructions Installation InstructionsPlug Acts as Disconnect Device Cable camera IndexHardware setting up 2-1troubleshooting Regulatory notices Safety and Regulatory Notices-1 Warranty information Safety and Regulatory Notices-4