Polycom 3725-24004-001/A manual 10’ 15’ 20’ 25’ 30’ 35’ 40’ 45’ 50’

Page 29

Using the Polycom PowerCam Presenter

Place the camera so that:

It is no more than 50 feet (15 meters) and no closer than 5 feet (1½ meters) from the person wearing the locator pack assembly.

It is about 6 feet to 7 feet (2 meters) above the floor, although higher will also work.

The back of the camera is at least 1 foot (½ meter) away from the wall. If you add acoustic foam on the wall, you can place the camera slightly closer than 1 foot (½ meter) from the wall.

The head of the camera points no more than 25 degrees above or below the camera base when it is tracking the person wearing the locator. Plus or minus 25 degrees of tilt is the mechanical limit of the camera.

Remove as many obstructions as possible between the locator pack assembly and the camera. Line-of-sight is best.

Face toward the camera when wearing the locator pack assembly. If you walk behind an obstruction or turn your back for a time and the system loses the ultrasound signal, move the locator pack assembly back in the line-of-sight of the camera. The camera will automatically receive the signal again and point toward you.

For best results, follow these guidelines:

From 5 feet (1½ meters) to 35 feet (11 meters) away from the camera, you can face the camera or turn side-to-side as long as the locator faces

no more than 90° away from the center of the camera.

5’

10’

15’

20’

25’

30’

35’

40’

45’

50’

55’

90°

camera

locator

90°

2 - 17

Image 29
Contents VideoVoiceDataWeb License Terms Trademark InformationAbout this Guide User’s Guide for the Polycom PowerCam Presenter Contents Maintenance and Troubleshooting Introducing the Polycom PowerCam Presenter Name Component Description System ComponentsTilt, or zoom VSX Series , available at Setting up the Polycom PowerCam Presenter State-of-the-Art Technology Key FeaturesEase of Use Setting up the Hardware Using the Polycom PowerCam PresenterUsing the Remote Control Setting Description Input Signal Configuring User SettingsConfiguring Camera Settings Backlight Compensation Setting Description Camera DirectionRestricted Unrestricted Not Specified Unrestricted Calibrating for Background Noise Calibrating the CameraConfiguring LAN Properties Configuring Video Output Settings Setting Description Output Using Automatic Camera TrackingOn-screen Connected to connector On the controller Display messagesEnabling and Disabling Automatic Camera Tracking Setting and Using Presenter Views Using the Polycom PowerCam Presenter Enabling and Disabling Automatic Zooming Controlling the Camera Manually Setting and Using Camera PresetsObtaining System Information Tips on Using the Polycom PowerCam Presenter10’ 15’ 20’ 25’ 30’ 35’ 40’ 45’ 50’ 10’ 15’ 20’ 25’ 30’ 35’ 40’ 45’ 50’ Charging the Locator Pack Batteries Maintenance and TroubleshootingMaintaining the System Upgrading the Software Automatic Camera Tracking SpecificationsSpecification Description Symptom Problem Corrective Action Troubleshooting the SystemPower and Hardware Issues To Composite Set the Input Signal to S-Video Set the Input Signal to CompositeOff Camera Movement IssuesLeft Right Down Automatic camera Camera inputs and outputs System Settings Appearance Go to System Admin Settings General SettingsSet to Restricted or Set Screen Saver Wait Time to OffContacting Technical Support User’s Guide for the Polycom PowerCam Presenter Important Safeguards Safety and Regulatory NoticesSafety Precautions for Lithium Ion Battery Packs ChargingSafety Warnings When Using the Battery Safety Warnings When Discharging the Battery License Restrictions Warranty InformationWarranty Information Industry Canada IC Regulatory NoticesPart 15 FCC Rules Safety and Regulatory Notices Plug Acts as Disconnect Device Regulatory Notices Special Safety InstructionsInstallation Instructions Cable camera IndexHardware setting up 2-1troubleshooting Regulatory notices Safety and Regulatory Notices-1 Warranty information Safety and Regulatory Notices-4