Kenwood instruction manual Channel Setup Mode, TK-2200 K2 TK-3200 K2 Channel Model

Page 25

CHANNEL SETUP MODE

This transceiver allows you to reprogram each of the channels with different frequencies and Quiet Talk/ Digital Quiet Talk settings. The table below lists the default channel frequencies. All channels are set with a 67.0 Hz QT tone by default.

Channel

Table

Frequency (MHz)

Table

Frequency (MHz)

Number

Number

Number

 

 

 

 

 

 

 

 

 

 

 

TK-2200 (K)

 

TK-3200 (K)

 

2-Channel Model

2-Channel Model

 

 

 

 

 

 

 

1

3

 

154.5700

2

 

464.5500

 

 

 

 

 

 

 

2

4

 

154.6000

8

 

467.9250

 

 

 

 

 

 

 

 

 

TK-2200 (K2)

 

TK-3200 (K2)

 

8-Channel Model

8-Channel Model

 

 

 

 

 

 

 

1

3

 

154.5700

2

 

464.5500

 

 

 

 

 

 

 

2

4

 

154.6000

8

 

467.9250

 

 

 

 

 

 

 

3

5

 

151.7000

9

 

461.0375

 

 

 

 

 

 

 

4

6

 

151.7600

10

 

461.0625

 

 

 

 

 

 

 

5

7

 

151.8200

11

 

461.0875

 

 

 

 

 

 

 

6

8

 

151.8800

12

 

461.1125

 

 

 

 

 

 

 

7

9

 

151.9400

13

 

461.1375

 

 

 

 

 

 

 

8

10

 

151.5125

14

 

461.1625

 

 

 

 

 

 

 

Note:

◆If you do not select an operating frequency for a channel, you will not be able to select a Quiet Talk/ Digital Quiet Talk setting for that same channel.

◆: For operating frequencies 151.8200 (MHz), 151.8800 (MHz), and 151.9400 (MHz), the transmit power is fixed at 1 W.

17

Page 24 Page 26
Image 25
Page 24 Page 26
Contents
TK-2200 Thank YOU Operating Conditions FCC License Information Explosive Atmospheres GASES, DUST, FUMES, etc IiiOne or more of the following statements may be applicable Page Contents Unpacking and Checking Equipment Warranty card B62-1791-XXQuantity Jack cover Rapid battery charger AC adaptor Ni-MH battery packAntenna optional OrientationPreparation Pack from the charger INSTALLING/ Removing the Battery Pack Installing the Optional Antenna Installing the Cover Over the SPEAKER/ Microphone Jacks Rotate the Channel selector to select your desired channel Getting StartedVoice Operated Transmission VOX Turning the transceiver power onPress and hold the Lock key while VOX Gain level and the Scan key Press the Lock key to increaseTo decrease the level To exit VOX mode, set the VOX Gain level page 10 to OFF To stop transmitting, stop speakingKEY Functions To end Scan, press the Scan key again To start scanning, press the Scan keyBackground Operations Quiet Talk QT/ Digital Quiet Talk DQT TK-2200 K2 TK-3200 K2 Channel Model Channel Setup ModeRotate the Channel selector to your Release the PTT switch and Lock keyDesired channel Press the Lock key to incrementOFF TK-2200 OperatingTK-3200 Operating Press the Lock key or Scan key to select QT or DQT setup New tone or code Tone number or the Scan key toOff QT Channel Settings103.5 Hz 167.9 Hz 107.2 Hz 173.8 Hz DQT DQT Channel SettingsFunction Name KEY Assignment ModeBe reprogrammed either the Lock key Continue to press and hold the key toOr the Scan key, while releasing Remaining keyOperation will cancel To save the setting, otherwiseTurn the transceiver power OFF Calling Alert MONITOR/ Squelch OFF Temporary Delete Transceiver power on ALL Reset ModeScan key while turning Release the keysOptional Accessories Problem Solution Troubleshooting GuideBattery pack may be dead