Dukane 8914 user manual Option Menu, Auto Search Auto OFF Lamp Time Filter Time, Reset  Cancel

Page 38

Multifunctional settings

OPTION Menu

With the OPTION menu, the items shown in the table below can be performed.

Select an item using the cursor buttons ▲/▼ on the projector or remote co ntrol, and press the cursor button ► on the projector or remote control, or the ENTER button on the remote control to execute the item , except for the items LAMP TIME and FILTER TIME. Then perform it referring to the following table.

 MENU [RGB]

   :SELECT

 PICTURE

 AUTO SEARCH  TURN OFF

 IMAGE

 AUTO OFF      0

 INPUT

 LAMP TIME     0

 SETUP

 FILTER TIME   0

 SCREEN

 SERVICE

 OPTION

 

 EASY MENU

 

Item

AUTO SEARCH

AUTO OFF

LAMP TIME

FILTER TIME

Description

Using the buttons ▲/▼ turns on/off the automatic signal search function

TURN ON TURN OFF

This function works with INPUT, RGB, and VIDEO buttons.

When the TURN ON is selected, detecting no signal automatically cycles through input ports i n the following order. The search is started from the current port. Then when an input is found, the projector will stop searching and display the image

RGB IN1 RGB IN2 COMPONENT VIDEO S-VIDEO VIDEO

Using the buttons ▲/▼ adjusts the time to count down to automatically turn the projector off

Long (max. 99 minutes) Short (min. 0 minute = DISABLE)

AUTO OFF

AUTO OFF

ENABLE

DISABLE

1

0

When the time is set to 0, the projector is not turned off automatically. When the time is set to 1 to 99, and when the passed time with no- signal or an unsuitable signal reaches at the set time, the projector lamp will go off and the power indicator begins blinking. Please refer to the section “Turning off the power” ( 16)

The lamp time is the time counted after the last resetting. It is shown in the OPTION menu as the usage time of the lamp. Pressing the RESET button on the remote control or the button ► of the projector displays a dialog To reset the lamp time select the RESET using the button ▲.

RESET CANCEL

Please reset the lamp time only when you have replaced the lamp for a corresponding message about the lamp

For the lamp replacement, see the section "Lamp" ( 38, 39)

The fi lter time is the time counted after the last resetting. It is shown in the OPTION menu as the usage time of the air fi lter

Pressing the RESET button on the remote control or the button ► of the projector displays a dialog. To reset the fi lter time, select the RESET using the button ▲.

RESET CANCEL

Please reset the fi lter time only when you have cleaned or replaced the air fi lter, for a corresponding message about the air fi lter

For the air fi lter cleaning see the section "Air fi lter ( 40)

36

Image 38
Contents Model Page Trademark acknowledgment About this manualThank you for purchasing this projector Content Fastening the lens cover Projector featuresPreparations Component Part namesProjector CB/PBMagnify Remote controlControl buttons Setting up Arrangement For the model 8914/8915Adjusting the projectors elevator About the filter cover for bottom-up use Connecting your devices About Plug-and-Play capabilityExamples of connection with a computer Connecting to a monitor outputConnecting to a speaker with amplifier output Video out Audio L out Examples of connection with a VCR/DVD playerAudio/Video cable Audio R outConnecting power supply Remote control Putting batteriesUsing the remote control Turning off the power Power on/offTurning on the power STANDBY/ONOperating Adjusting the volumeSelecting an input signal Temporarily muting the sound For an RGB signal Searching an input signalAdjusting the zoom and focus  For a video signal/no signal For a video signal or s-video signal Using the automatic adjustment featureAdjusting the position  For a component video signalUsing the magnify feature Correcting the keystone distortionsFreezing the screen Temporarily blanking the screenEasy Menu Multifunctional settingsUsing the menu function Advanced MenuDescription Aspect Mode Brightness Contrast Color Tint Shrpness WhisperEasy Menu Go To Advanced Menu Description Mirror Reset Filter Time LanguageEasy Menu Gamma #3 Custom  #3 Default  #2 CustomPicture Menu High  Middle  LOW  Custom Picture MenuColor Temp Color Tint SharpnessLOAD1  LOAD2  LOAD3  LOAD4 SAVE4 SAVE3  SAVE2  SAVE1 Progressive MY MemoryTV  Film  Turn OFF For a video signal / no signal 43  169  Small Aspect Over Scan Position PhaseFor an RGB signal Image MenuImage Menu Size Auto Adjust ExecuteFor a video signal or s-video signal Compo Nent  Scart RGB Input MenuColor Space Component Video Format Auto  Ntsc  PAL  SecamInput Menu InformationAudio Setup MenuWhisper Mirror Volume Bright  Dark Screen MenuMenu Position OSD Bright Blank MyScreen MyScreen Lock Description Screen MenuStart UP Turn on  Turn OFFMessage No Input is Detected Sync is OUT of RangeAuto Search Auto OFF Lamp Time Filter Time Reset  CancelOption Menu Option Menu Maintenance LampCase of replacement by yourself LampAir filter Inside of the projector Caring for the cabinet and remote controlOther care Caring for the lensRelated messages Time the lamp timer has counted is approaching 2000 hoursThere is no input signal Internal temperature is rising Related messagesPossibility that interior portion has become Regarding the indicator lampsLamp does not light, and there is a HeatedCooling fan is not operating Regarding the indicator lampsIt is time to clean the ai r filter There is a possibility that the interior portionSignal cables are not correctly connected Electrical power cord is not pluggedPower switch is not set to the on position Volume is adjusted to an extremely low levelColor Space setting is not suitable Brightness is adjusted to an extremely low levelColor settings are not correctly adjusted Lens cap is attachedRGB output SpecificationRGB input Audio inputSpecifications Page Vesa Example of computer signalVesa Text Initial set signals Connection to the ports RGB in 1, B RGB in 2, C RGB OUTComponent Video D Y, E CB/PB F CR/PR CTS Audio 1-IN Ø3.5 stereo mini jack, I J Audio 2 L/R RCA jackRTS RS-232C Communication Connecting the cableCommunications setting Using the projector default settings Reset Command Requesting projector status Get commandChanging the projector settings Set command Increasing the projector setting value Increment commandRS-232C Communication Be EF FB FA Color Temp Gain G Aspect Keystone Mute OSD Bright Page Audio Visual Products