Dukane 8914 user manual Lamp, Case of replacement by yourself

Page 41

Lamp cover

Maintenance

Lamp (continued)

When the indicators or a message prompt you to replace the lamp, replace the lamp as soon as possible.

1. Turn the projector off, and unplug the power cord. Allow the lamp to cool for at least 45 minutes.

2. To prepare a new lamp, contact your dealer and tell the lamp type number = 456-8915.If the projector is mounted on the ceiling, or if the lamp has

broken, also ask the dealer to replace the lamp

In the case of replacement by yourself,

3. After making sure that the projector has cooled adequately, slowly turn over the projector, so that the bottom is facing up.

4. Please unhook the claws of the lamp cover and remove the lamp cover.

5. Loosen the 2 screws (marked by arrow) of the lamp, and slowly pick up the lamp by the

handles.

6. Insert the new lamp, and retighten ﬁ rmly the two screws that are loosened in the previous

process to lock it in place.

7. While interlocking the 2 tabs of the lamp cover to the projector, position the lamp cover

on the projector. Then push the center point of the two claws to ﬁ x the lamp cover.

8. Slowly turn the projector so that the top is facing up.

9. Turn the projector on, and reset the lamp time using the LAMP TIME function in the

OPTION menu ( 36)

Claws

Screws marked

by arrow

Tabs

Center point of claws

Claw

NOTE • When the lamp has been replaced after the message of "THE POWER WILL TURN OFF AFTER 0hr." is displayed, complete the following operation within 10 minutes of switching power on.

•Incorrectly resetting of the lamp timer (resetting without replacement, or neglect of resetting after replacement) will result in incorrect message functions.

39

Image 41

Contents Model Page Trademark acknowledgment About this manualThank you for purchasing this projector Content Fastening the lens cover Projector featuresPreparations Projector Part namesComponent CB/PBMagnify Remote controlControl buttons Setting up For the model 8914/8915 ArrangementAdjusting the projectors elevator About the ﬁlter cover for bottom-up use About Plug-and-Play capability Connecting your devicesExamples of connection with a computer Connecting to a monitor outputConnecting to a speaker with ampliﬁer output Audio/Video cable Examples of connection with a VCR/DVD playerVideo out Audio L out Audio R outConnecting power supply Putting batteries Remote controlUsing the remote control Turning on the power Power on/offTurning off the power STANDBY/ONSelecting an input signal Adjusting the volumeOperating Temporarily muting the soundAdjusting the zoom and focus Searching an input signal For an RGB signal  For a video signal/no signalAdjusting the position Using the automatic adjustment feature For a video signal or s-video signal  For a component video signalCorrecting the keystone distortions Using the magnify featureTemporarily blanking the screen Freezing the screenUsing the menu function Multifunctional settingsEasy Menu Advanced MenuDescription Aspect Mode Brightness Contrast Color Tint Shrpness WhisperEasy Menu Go To Advanced Menu Description Mirror Reset Filter Time LanguageEasy Menu Gamma #3 Custom  #3 Default  #2 CustomPicture Menu Color Temp Picture MenuHigh  Middle  LOW  Custom Color Tint SharpnessLOAD1  LOAD2  LOAD3  LOAD4 SAVE4 SAVE3  SAVE2  SAVE1 Progressive MY MemoryTV  Film  Turn OFF For an RGB signal Aspect Over Scan Position PhaseFor a video signal / no signal 43  169  Small Image MenuImage Menu Size Auto Adjust ExecuteFor a video signal or s-video signal Color Space Component Video Format Input MenuCompo Nent  Scart RGB Auto  Ntsc  PAL  SecamInformation Input MenuAudio Setup MenuWhisper Mirror Volume Bright  Dark Screen MenuMenu Position OSD Bright Blank Start UP Screen MenuMyScreen MyScreen Lock Description Turn on  Turn OFFNo Input is Detected Sync is OUT of Range MessageAuto Search Auto OFF Lamp Time Filter Time Reset  CancelOption Menu Option Menu Lamp MaintenanceLamp Case of replacement by yourselfAir ﬁlter Other care Caring for the cabinet and remote controlInside of the projector Caring for the lensRelated messages Time the lamp timer has counted is approaching 2000 hoursThere is no input signal Related messages Internal temperature is risingLamp does not light, and there is a Regarding the indicator lampsPossibility that interior portion has become HeatedIt is time to clean the ai r ﬁlter Regarding the indicator lampsCooling fan is not operating There is a possibility that the interior portionPower switch is not set to the on position Electrical power cord is not pluggedSignal cables are not correctly connected Volume is adjusted to an extremely low levelColor settings are not correctly adjusted Brightness is adjusted to an extremely low levelColor Space setting is not suitable Lens cap is attachedRGB input SpeciﬁcationRGB output Audio inputSpeciﬁcations Page Vesa Example of computer signalVesa Text Initial set signals RGB in 1, B RGB in 2, C RGB OUT Connection to the portsComponent Video D Y, E CB/PB F CR/PR CTS Audio 1-IN Ø3.5 stereo mini jack, I J Audio 2 L/R RCA jackRTS RS-232C Communication Connecting the cableCommunications setting Changing the projector settings Set command Requesting projector status Get commandUsing the projector default settings Reset Command Increasing the projector setting value Increment commandRS-232C Communication Be EF FB FA Color Temp Gain G Aspect Keystone Mute OSD Bright Page Audio Visual Products