Dukane 8914 Specification, RGB input, RGB output, Audio input, Audio output, Video input

Page 50

Warranty And After-Service

Warranty and after-service

If a problem occurs with the equipment, fi rst refer to the “Troubleshooting” and run through the suggested checks. If this does not resolve the problem, please contact your dealer or service company. They will tell you what warranty condition is applied.

Specifications

Specifi cations

NOTE • These specifi cations are subject to change without notice.

Item

Product name

Liquid

Panel size

 

Crystal

Drive system

panel

Pixels

 

Lens

 

Lamp

 

Speaker

Power Supply

Power Consumption

Temperature range

Size

Weight (mass)

Specification

Liquid crystal projector

CP-X444 : 2 .0 cm (0.79 type)

CP-X440 : 1.8 cm (0.7 type)

TFT active matrix

786 432 pixels ( 1024 horizontal x 768 vertical)

CP-X444 : Zoom lens F= 1.7 ~ 2 1 f=24.4 ~ 29. 3 mm

CP-X440 : Zoom lens F= 1.7 ~ 1. 9 f=2 1.8 ~ 26.2 mm

230W UHB

1 W x 1

AC100-120V/4 0A, AC220-240V/2 0A

370W

5 ~ 35°C (Operating)

336 (W) x 95 (H) x 265 (D) mm (Not including protruding parts)

• Please refer to the following fi gure.

CP-X444 : 3 7 kg, 8.2 lb.

CP-X440 : 3 5 kg

Ports

Lamp

Optional

RGB input:

RGB IN1

D-sub 15pin mini x1

RGB IN2

D-sub 15pin mini x1

RGB output:

RGB OUT D-sub 15pin mini x1

Audio input:

 

AUDIO 1

Stereo mini x1

AUDIO 2

RCA x2

Audio output:

AUDIO OUT Stereo mini x1 456-8915

Video input:

 

 

COMPONENT VIDEO

 

(Y, CB/PB, CR/PR)

RCA x3

S-Video

 

1

Video

 

1

Communication port:

 

CONTROL

D-sub 9pin x1

parts

Air fi lter

Others

NJ20642

• Please consult your dealer.

48

Image 50
Contents Model Page Trademark acknowledgment About this manualThank you for purchasing this projector Content Fastening the lens cover Projector featuresPreparations Component Part namesProjector CB/PBMagnify Remote controlControl buttons Setting up Arrangement For the model 8914/8915Adjusting the projectors elevator About the filter cover for bottom-up use Connecting your devices About Plug-and-Play capabilityExamples of connection with a computer Connecting to a monitor outputConnecting to a speaker with amplifier output Video out Audio L out Examples of connection with a VCR/DVD playerAudio/Video cable Audio R outConnecting power supply Remote control Putting batteriesUsing the remote control Turning off the power Power on/offTurning on the power STANDBY/ONOperating Adjusting the volumeSelecting an input signal Temporarily muting the sound For an RGB signal Searching an input signalAdjusting the zoom and focus  For a video signal/no signal For a video signal or s-video signal Using the automatic adjustment featureAdjusting the position  For a component video signalUsing the magnify feature Correcting the keystone distortionsFreezing the screen Temporarily blanking the screenEasy Menu Multifunctional settingsUsing the menu function Advanced MenuDescription Aspect Mode Brightness Contrast Color Tint Shrpness WhisperEasy Menu Go To Advanced Menu Description Mirror Reset Filter Time LanguageEasy Menu Gamma #3 Custom  #3 Default  #2 CustomPicture Menu High  Middle  LOW  Custom Picture MenuColor Temp Color Tint SharpnessLOAD1  LOAD2  LOAD3  LOAD4 SAVE4 SAVE3  SAVE2  SAVE1 Progressive MY MemoryTV  Film  Turn OFF For a video signal / no signal 43  169  Small Aspect Over Scan Position PhaseFor an RGB signal Image MenuImage Menu Size Auto Adjust ExecuteFor a video signal or s-video signal Compo Nent  Scart RGB Input MenuColor Space Component Video Format Auto  Ntsc  PAL  SecamInput Menu InformationAudio Setup MenuWhisper Mirror Volume Bright  Dark Screen MenuMenu Position OSD Bright Blank MyScreen MyScreen Lock Description Screen MenuStart UP Turn on  Turn OFFMessage No Input is Detected Sync is OUT of RangeAuto Search Auto OFF Lamp Time Filter Time Reset  CancelOption Menu Option Menu Maintenance LampCase of replacement by yourself LampAir filter Inside of the projector Caring for the cabinet and remote controlOther care Caring for the lensRelated messages Time the lamp timer has counted is approaching 2000 hoursThere is no input signal Internal temperature is rising Related messagesPossibility that interior portion has become Regarding the indicator lampsLamp does not light, and there is a HeatedCooling fan is not operating Regarding the indicator lampsIt is time to clean the ai r filter There is a possibility that the interior portionSignal cables are not correctly connected Electrical power cord is not pluggedPower switch is not set to the on position Volume is adjusted to an extremely low levelColor Space setting is not suitable Brightness is adjusted to an extremely low levelColor settings are not correctly adjusted Lens cap is attachedRGB output SpecificationRGB input Audio inputSpecifications Page Vesa Example of computer signalVesa Text Initial set signals Connection to the ports RGB in 1, B RGB in 2, C RGB OUTComponent Video D Y, E CB/PB F CR/PR CTS Audio 1-IN Ø3.5 stereo mini jack, I J Audio 2 L/R RCA jackRTS RS-232C Communication Connecting the cableCommunications setting Using the projector default settings Reset Command Requesting projector status Get commandChanging the projector settings Set command Increasing the projector setting value Increment commandRS-232C Communication Be EF FB FA Color Temp Gain G Aspect Keystone Mute OSD Bright Page Audio Visual Products