BenQ MP720 user manual Introduction, Projector features

Page 11

Introduction

Projector features

The projector integrates high-performance optical engine projection and a user-friendly design to deliver high reliability and ease of use.

The projector offers the following features:

•Selectable password protected function

•Selectable quick cooling function for reducing projector cooling time

•Optional wireless module allowing more computers to share one projector through cable or wireless connection

•Compact and portable unit

•High quality manual zoom lens

•One-key auto-adjustment to display the best picture quality

•Digital keystone correction to correct distorted images

•Adjustable color balance control for data/video display

•Ultra-high brightness projection lamp

•Ability to display 16.7 million colors

•Multi-language on-screen menus

•Switchable normal and Economic modes to reduce the power consumption

•Built-in speaker provides mixed mono audio when an audio input is connected

•Powerful AV function to provide high quality AV picture

•Component HDTV compatibility (YPbPr)

•The apparent brightness of the projected image will vary depending on the ambient

lighting conditions, selected input source contrast/brightness settings, and is directly proportional to projection distance.

•The lamp brightness will decline over time and may vary within the lamp manufacturers specifications. This is normal and expected behavior.

Introduction 5

Image 11

Contents Welcome Disclaimer CopyrightTable of contents Supported timing for Component-YPbPr input Iv Table of contentsRegulation Statements Table of contentsMemo Vi Table of contents Important safety instructions Important safety instructionsRefer servicing to qualified service personnel But could fail if power cuts or surgesSafety Instructions Bedding or any other soft surface Safety Instructions Introduction Projector featuresIntroduction Shipping contents Rear side Projector exterior viewFront / upper side Lamp cover Side viewLower side Kensington anti-theft lock slotTurns the projector on or off Controls and functionsExternal control panel InformationII/ Freeze Remote controlExit 5Up, 6 Down 3Left, Right4 Operating the projector from Remote control effective rangeReplacing the remote control battery Pull out the battery holderPositioning your projector Positioning your projectorChoosing a location Floor front Obtaining a preferred projected image size Positioning your projector 1500 Maximum zoom Minimum zoomScreen Center of lens Projection distance 1219Cable connection Wireless connection optionalConnecting a computer or monitor ConnectionVGA VGA-DVI With a VGA cable With a VGA-DVI cable Connecting a monitorBest video quality Connecting Video source devicesConnecting a Component Video source device Connecting an S-Video source device Connecting a composite Video source device Start up Utilizing the password functionOperation To change the password To set a passwordIf you forget the password To enter the password recall procedureAuto-adjusting the image Adjusting the heightCorrecting keystone Fine-tuning the image size and clarityAdjust the projected image to the size That you need using the zoom ring Focus ringMovie default Cinema Gaming Photo Selecting an application modeSwitching input signal Brightest default Presentation SRGB/Photo Gaming VideoShutdown Power indicator light flashesRemote paging operations Freezing the imageMenu system Menu operationUsing the menus Picture menu Brightness Color TempDepends on SelectedPro-Picture menu Setting menu Advance menu Economic Mode offHigh Altitude Auto Off offLamp Hour System ResolutionMode Equivalent Information menuCare of the projector MaintenanceTo clean the filter How to replace the filter sponge Message Status Lamp informationCalculation of lamp hour Replacing the lamp Disconnect the lamp connector from the projector MaintenanceMaintenance Iii. Wait about 5 seconds to let the OSD disappear Temperature informationResetting the lamp counter Restart the projectorStand-by mode IndicatorsLight Status & Description Power Temp Lamp Power events Light Status & Description Power Temp Lamp Lamp eventsFor assistance Thermal eventsMaintenance Cause Remedy TroubleshootingPlug the power cord into the AC inlet on Make sure that it is switched onProjector specifications SpecificationsSupported timing for Video and S-Video inputs Timing chartSupported timing for PC input Supported timing for Component-YPbPrinputUnit mm Specifications DimensionsLimited Warranty WarrantyMIC statement Regulation StatementsFCC statement EEC statement