BenQ MP720 user manual Advance menu

Page 43

4. Advance menu

	FUNCTION
	(default setting	DESCRIPTION
	/ value)
	Mirror (Floor	The projector can be installed on a ceiling or behind a screen, or with one
	Mirror (Floor	or more mirrors. Contact your dealer for the ceiling mount bracket
	front)	(optional accessory) if you need to install the projector on your ceiling.
		Refer to "Choosing a location" on page 13 for more information.
	Blank Time	Sets the image blank time when the Blank feature is activated, once
	Blank Time	elapsed the image will return to the screen.
	(20)	elapsed the image will return to the screen.
	(20)

	Source Scan	Sets whether the projector searches automatically for input signals. If the
	Source Scan	source scan is On, the projector will scan for input signals until it acquires
	(on)	a signal. If the function is not activated, the projector selects the last used
		input signal. The default value is `RGB'.
	Language	Language sets the language for the OSD control menus.
	Language	Use Left 3/ Right 4on the projector or Left 3/ Right 4on the remote
	(English)
		control to select your desired language.
	Splash	Allows you to select which logo screen will display during projector start-
	Splash	up. Three modes are available: Default (BenQ logo), black screen or blue
	Screen
	Screen	screen.
	(BenQ logo)

Operation 37

Image 43

Contents Welcome Disclaimer CopyrightTable of contents Supported timing for Component-YPbPr input Iv Table of contentsRegulation Statements Table of contentsMemo Vi Table of contents Important safety instructions Important safety instructionsRefer servicing to qualified service personnel But could fail if power cuts or surgesSafety Instructions Bedding or any other soft surface Safety Instructions Introduction Projector featuresIntroduction Shipping contents Front / upper side Projector exterior viewRear side Lamp cover Side viewLower side Kensington anti-theft lock slotTurns the projector on or off Controls and functionsExternal control panel InformationExit Remote controlII/ Freeze 5Up, 6 Down 3Left, Right4 Operating the projector from Remote control effective rangeReplacing the remote control battery Pull out the battery holderChoosing a location Positioning your projectorPositioning your projector Floor front Obtaining a preferred projected image size Positioning your projector 1500 Maximum zoom Minimum zoomScreen Center of lens Projection distance 1219Cable connection Wireless connection optionalConnecting a computer or monitor ConnectionVGA VGA-DVI With a VGA cable With a VGA-DVI cable Connecting a monitorBest video quality Connecting Video source devicesConnecting a Component Video source device Connecting an S-Video source device Connecting a composite Video source device Operation Utilizing the password functionStart up To change the password To set a passwordIf you forget the password To enter the password recall procedureAuto-adjusting the image Adjusting the heightCorrecting keystone Fine-tuning the image size and clarityAdjust the projected image to the size That you need using the zoom ring Focus ringMovie default Cinema Gaming Photo Selecting an application modeSwitching input signal Brightest default Presentation SRGB/Photo Gaming VideoShutdown Power indicator light flashesRemote paging operations Freezing the imageMenu system Menu operationUsing the menus Picture menu Brightness Color Temp Depends on SelectedPro-Picture menu Setting menu Advance menu Economic Mode offHigh Altitude Auto Off offLamp Hour System ResolutionMode Equivalent Information menuCare of the projector MaintenanceTo clean the filter How to replace the filter sponge Calculation of lamp hour Lamp informationMessage Status Replacing the lamp Disconnect the lamp connector from the projector MaintenanceMaintenance Iii. Wait about 5 seconds to let the OSD disappear Temperature informationResetting the lamp counter Restart the projectorStand-by mode IndicatorsLight Status & Description Power Temp Lamp Power events Light Status & Description Power Temp Lamp Lamp eventsFor assistance Thermal eventsMaintenance Cause Remedy TroubleshootingPlug the power cord into the AC inlet on Make sure that it is switched onProjector specifications SpecificationsSupported timing for Video and S-Video inputs Timing chartSupported timing for PC input Supported timing for Component-YPbPrinputUnit mm Specifications DimensionsLimited Warranty WarrantyMIC statement Regulation StatementsFCC statement EEC statement