BenQ MP720 user manual Menu operation, Menu system

Page 37

Menu operation

Menu system

Please note that the on-screen display (OSD) menus vary according to the signal type selected.

						Functions available when receiving different signal types...

	Sub-Menu					PC / DVI-A	Wireless /	Video / S-	Component
	Sub-Menu					PC / DVI-A	DVI-D	Video	Video
							DVI-D	Video	Video
						Application Mode		Application Mode
						Keystone		Keystone
						Keystone		Keystone
						Color Temp		Color Temp
						Brightness		Brightness
						Brightness		Brightness
	Picture					Contrast		Contrast
	Picture							Color
								Tint*

						Auto Resize	Auto Resize (not	Auto Resize
						Aspect Ratio	available with	Aspect Ratio
						Aspect Ratio	available with	Aspect Ratio
						H Position	Wireless	Sharpness
						H Position	Wireless	Sharpness
						V Position	selected)
	Pro-Picture					Phase	Aspect Ratio
						H. Size
						Mute
						Volume
						Volume
						OSD Time
						Quick Cooling
						Quick Cooling
	Setting					Password
	Setting					Change Password
						Reset

						Mirror
						Blank Time
						Source Scan
						Source Scan
						Language
						Language
						Splash Screen
	Advance					High Altitude Mode
						Auto Off
						Economic Mode

						Source		Source	Source
						Resolution		System	Resolution
						Resolution		System	Resolution
						Application Mode		Application	Application
						Application Mode		Application	Application
						Equivalent Lamp Hour		Mode	Mode
	Information							Equivalent Lamp	Equivalent Lamp
								Hour	Hour

*When a Video or S-Video signal is connected, the function is only available with NTSC system selected.

Operation 31

Image 37

Contents Welcome Disclaimer CopyrightTable of contents Supported timing for Component-YPbPr input Iv Table of contentsRegulation Statements Table of contentsMemo Vi Table of contents Refer servicing to qualified service personnel Important safety instructionsBut could fail if power cuts or surges Important safety instructionsSafety Instructions Bedding or any other soft surface Safety Instructions Introduction Projector featuresIntroduction Shipping contents Front / upper side Projector exterior viewRear side Lower side Side viewKensington anti-theft lock slot Lamp coverExternal control panel Controls and functionsInformation Turns the projector on or offExit Remote controlII/ Freeze 5Up, 6 Down 3Left, Right4 Replacing the remote control battery Remote control effective rangePull out the battery holder Operating the projector fromChoosing a location Positioning your projectorPositioning your projector Floor front Obtaining a preferred projected image size Positioning your projector Screen Center of lens Projection distance Maximum zoom Minimum zoom1219 1500Connecting a computer or monitor Wireless connection optionalConnection Cable connectionVGA VGA-DVI With a VGA cable With a VGA-DVI cable Connecting a monitorBest video quality Connecting Video source devicesConnecting a Component Video source device Connecting an S-Video source device Connecting a composite Video source device Operation Utilizing the password functionStart up If you forget the password To set a passwordTo enter the password recall procedure To change the passwordAuto-adjusting the image Adjusting the heightAdjust the projected image to the size Fine-tuning the image size and clarityThat you need using the zoom ring Focus ring Correcting keystoneSwitching input signal Selecting an application modeBrightest default Presentation SRGB/Photo Gaming Video Movie default Cinema Gaming PhotoRemote paging operations Power indicator light flashesFreezing the image ShutdownMenu system Menu operationUsing the menus Picture menu Depends on Color TempSelected BrightnessPro-Picture menu Setting menu Advance menu High Altitude Mode offAuto Off off EconomicMode Equivalent ResolutionInformation menu Lamp Hour SystemCare of the projector MaintenanceTo clean the filter How to replace the filter sponge Calculation of lamp hour Lamp informationMessage Status Replacing the lamp Disconnect the lamp connector from the projector MaintenanceMaintenance Resetting the lamp counter Temperature informationRestart the projector Iii. Wait about 5 seconds to let the OSD disappearLight Status & Description Power Temp Lamp Power events IndicatorsLight Status & Description Power Temp Lamp Lamp events Stand-by modeFor assistance Thermal eventsMaintenance Plug the power cord into the AC inlet on TroubleshootingMake sure that it is switched on Cause RemedyProjector specifications SpecificationsSupported timing for PC input Timing chartSupported timing for Component-YPbPrinput Supported timing for Video and S-Video inputsUnit mm Specifications DimensionsLimited Warranty WarrantyFCC statement Regulation StatementsEEC statement MIC statement