BenQ MP720 user manual Projector exterior view, Front / upper side, Rear side

Page 13

Projector exterior view

Front / upper side

1

2

3

4

5

	1.	External control panel
		(See "External control panel" on
6		page 9 for detailed information.)
6	2.	Ventilation grill
7	3.	Projection lens
7	4.	Front adjuster button
	5.	Lens cap
	6.	Focus ring and Zoom ring
	7.	Front IR remote sensor

Rear side

Refer to "Connection" on page 18 for more information on making connections to various equipment.

	11 12	13	14	15	16	17	18	19	20
10
9									21
9
8
8.	Rear adjuster foot			15.	RGB (PC) / Component video (YPbPr/
9.	AC power cord inlet				YCbCr) signal input socket
10.	Filter case			16.	DVI-I signal input socket
11.	Rear IR remote sensor			17.	Video socket
12.	USB socket			18.	S-Video socket
13.	RS232 control port			19.	Audio input socket
14.	RGB signal output socket			20.	Audio output socket
				21.	Speaker

Introduction 7

Image 13

Contents Welcome Disclaimer CopyrightTable of contents Supported timing for Component-YPbPr input Iv Table of contentsRegulation Statements Table of contentsMemo Vi Table of contents Refer servicing to qualified service personnel Important safety instructionsBut could fail if power cuts or surges Important safety instructionsSafety Instructions Bedding or any other soft surface Safety Instructions Introduction Projector featuresIntroduction Shipping contents Front / upper side Projector exterior viewRear side Lower side Side viewKensington anti-theft lock slot Lamp coverExternal control panel Controls and functionsInformation Turns the projector on or offExit Remote controlII/ Freeze 5Up, 6 Down 3Left, Right4 Replacing the remote control battery Remote control effective rangePull out the battery holder Operating the projector fromChoosing a location Positioning your projectorPositioning your projector Floor front Obtaining a preferred projected image size Positioning your projector Screen Center of lens Projection distance Maximum zoom Minimum zoom1219 1500Connecting a computer or monitor Wireless connection optionalConnection Cable connectionVGA VGA-DVI With a VGA cable With a VGA-DVI cable Connecting a monitorBest video quality Connecting Video source devicesConnecting a Component Video source device Connecting an S-Video source device Connecting a composite Video source device Operation Utilizing the password functionStart up If you forget the password To set a passwordTo enter the password recall procedure To change the passwordAuto-adjusting the image Adjusting the heightAdjust the projected image to the size Fine-tuning the image size and clarityThat you need using the zoom ring Focus ring Correcting keystoneSwitching input signal Selecting an application modeBrightest default Presentation SRGB/Photo Gaming Video Movie default Cinema Gaming PhotoRemote paging operations Power indicator light flashesFreezing the image ShutdownMenu system Menu operationUsing the menus Picture menu Depends on Color TempSelected BrightnessPro-Picture menu Setting menu Advance menu High Altitude Mode offAuto Off off EconomicMode Equivalent ResolutionInformation menu Lamp Hour SystemCare of the projector MaintenanceTo clean the filter How to replace the filter sponge Calculation of lamp hour Lamp informationMessage Status Replacing the lamp Disconnect the lamp connector from the projector MaintenanceMaintenance Resetting the lamp counter Temperature informationRestart the projector Iii. Wait about 5 seconds to let the OSD disappearLight Status & Description Power Temp Lamp Power events IndicatorsLight Status & Description Power Temp Lamp Lamp events Stand-by modeFor assistance Thermal eventsMaintenance Plug the power cord into the AC inlet on TroubleshootingMake sure that it is switched on Cause RemedyProjector specifications SpecificationsSupported timing for PC input Timing chartSupported timing for Component-YPbPrinput Supported timing for Video and S-Video inputsUnit mm Specifications DimensionsLimited Warranty WarrantyFCC statement Regulation StatementsEEC statement MIC statement