BenQ W5000 Connecting Hdmi devices, Connecting Rgbhv devices, Connecting component-video devices

Page 17

W20000-en.book Page 17 Monday, October 22, 2007 3:35 PM

Connecting HDMI devices

You should use an HDMI cable when making connection between the projector and HDMI devices.

HDMI device: DVD player, digital tuner, etc.

From audio output	To audio input
terminals	terminals

HDMI
			Y	PB/CB PR/CR	S-VIDEO
			Y	PB/CB PR/CR	VIDEO
G/Y	B/PB/CB	R/PR/CR	H	V	RS-232
					12V TRIGGER

HDMI cable

You should also connect the separate audio cable to a suitable audio amplifier.

Connecting RGBHV devices

Use a RGBHV video cable with 5 BNC male connectors for connection. Be sure to match the corresponding colors between the cables and the terminals.

AV equipment: DVD player, digital tuner, etc.

From audio output	To audio input
terminals	terminals

BNC cable

Connecting component-video devices

Be sure to match the corresponding colors between the cables and the terminals.

AV equipment: DVD player, digital tuner, etc.

From audio output	To audio input
terminals	terminals	HDMI

			Y	PB/CB PR/CR	S-VIDEO
			Y	PB/CB PR/CR	VIDEO
G/Y	B/PB/CB	R/PR/CR	H	V	RS-232
					12V TRIGGER

Component cable	or

The RCA type component video sockets are provided for connection to video output devices. If you have a BNC type component video cable, you can alternatively connect through the BNC component video sockets.

You should also connect the separate audio cable to a suitable audio amplifier.

English

Connecting with video equipment

17

Image 17

Contents W20000/W5000 Digital Projector Home Cinema Series WelcomeTable of contents Important safety instructions Do not step on the projector or place any objects upon it Do not block the ventilation holes whileDuring operation. It may harm your sight Avoid volatile liquid Moisture condensationDisposal Ceiling mounting the projectorRemote control batteries Shipping contentsRemote control operation OverviewProjector features Projector exterior view Connector panelFront and upper side view Rear viewControl panel Controls and functionsRemote control Choosing a location Positioning your projectorShifting the projection lens vertically Obtaining a preferred projected image sizeDetermine the aspect ratio of your screen, 169 or 43? Installation for a 169 ratio screen Projection dimensionsWidescreen ratio screen dimension table With min Position Zoom Cm C Cm DDiagonal Installation for a 43 ratio screenMin Max Highest Lowest Image Preparations Connecting with video equipmentBest video quality Better video qualityConnecting component-video devices Connecting Hdmi devicesConnecting Rgbhv devices Connect the projector to a computer with a VGA-BNC cable Connecting S-Video or video devicesConnecting a computer Using the remote control or projector Using the projectorUsing the OSD menu Turning the projector onFine-tuning the image size and clarity Using the menusUse / to highlight the System Setup menu Adjust the projected picture to the size that youUtilizing the password function Using a security cable lockSetting a password If you forget the passwordChanging the password Entering the password recall procedureDisabling the password function Confirm the new password by re-entering the new passwordAdjusting the projection angle Adjusting the projected imageCorrecting picture distortion Two parallel sidesSelecting a preset mode Using the preset and user modesFine-tuning the selected picture mode Using the remote controlResetting the picture mode Setting the User 1/User 2/User 3 modeRenaming user modes Enter and ExitFine-tuning the picture quality Selecting a color temperature Setting Black LevelAdvanced picture quality controls Controlling image clarityTo set a preferred color temperature Setting a preferred color temperatureTo adjust and store the settings Color ManagementSelecting a Gamma setting Adjusting Brilliant ColorAdjusting contrast ratio via Iris Using the remote controlAbout the aspect ratio Their original width using this settingSelecting the aspect ratio To activate High Altitude Mode Using Panamorph lenses optionalOperating in a high altitude environment Suitable for use with PC and Rgbhd source inputsDisplaying more than one image source simultaneously Disabled functions for the active windowsPIP source conflict list Highlight PIP and press / to select OnLocking control keys Creating your own startup screenPersonalizing the projector menu display Commands during the cooling process Turning the power offOn-Screen Display OSD structure On-Screen Display OSD menusInformation System SetupSetup Picture -- Advanced menu Picture -- Basic menuDisplay menu System Setup menuAdvanced Setup menu Information menu ResolutionSource Lamp HoursCare of the projector Additional informationResetting the filter timer To clean the filterLamp information Setting Auto OffGetting to know the lamp hour Extending lamp lifeReplacing the lamp Timing of replacing the lampPulling it too quickly may cause the lamp to Tighten the screws securing the lamp boxAfter the startup logo, press Menu and then press / until Resetting the lamp timerIndicators Troubleshooting Dimensions SpecificationsOptical ElectricalFormat Resolution Refresh rateHz Freq.KHz Pixel Freq.MHz Timing chartSupported timing for Video and S-Video inputs Supported timing for Hdmi inputWarranty Warranty and Copyright informationCopyright DisclaimerFCC statement for United States users Regulation statementsEEC statement for European users MIC statement