BenQ W20000, W5000 user manual Turning the power off, Commands during the cooling process

Page 34

W20000-en.book Page 34 Monday, October 22, 2007 3:35 PM

English

Turning the power off

To turn the projector off, press POWER ( ) on the projector or remote control and a warning message appears. Press POWER again.

•The Power indicator light flashes orange and the fans run for about

two minutes to cool the lamp. The projector will not respond to any commands until the cooling process is complete.

•Then, the Power indicator light is a steady orange once the cooling

process has finished and fans stop.

• If the projector will not be used for an extended period, turn the

Power Off

main power switch off and unplug the power cable from the power outlet.

•

To protect the lamp, the projector will not respond to any

Press

 

again to power off.

 

 

commands during the cooling process.

 

 

 

 

 

 

Press any other button to cancel

34 Using the projector

Page 33 Page 35
Image 34
Page 33 Page 35
Contents Welcome W20000/W5000 Digital Projector Home Cinema SeriesTable of contents Important safety instructions During operation. It may harm your sight Do not block the ventilation holes whileDo not step on the projector or place any objects upon it Disposal Moisture condensationAvoid volatile liquid Ceiling mounting the projectorRemote control operation Shipping contentsRemote control batteries OverviewProjector features Front and upper side view Connector panelProjector exterior view Rear viewControls and functions Control panelRemote control Positioning your projector Choosing a locationObtaining a preferred projected image size Shifting the projection lens verticallyDetermine the aspect ratio of your screen, 169 or 43? Widescreen ratio screen dimension table Projection dimensionsInstallation for a 169 ratio screen With min Position Zoom Cm C Cm DMin Max Highest Lowest Image Installation for a 43 ratio screenDiagonal Best video quality Connecting with video equipmentPreparations Better video qualityConnecting Rgbhv devices Connecting Hdmi devicesConnecting component-video devices Connecting a computer Connecting S-Video or video devicesConnect the projector to a computer with a VGA-BNC cable Using the OSD menu Using the projectorUsing the remote control or projector Turning the projector onUse / to highlight the System Setup menu Using the menusFine-tuning the image size and clarity Adjust the projected picture to the size that youSetting a password Using a security cable lockUtilizing the password function If you forget the passwordDisabling the password function Entering the password recall procedureChanging the password Confirm the new password by re-entering the new passwordCorrecting picture distortion Adjusting the projected imageAdjusting the projection angle Two parallel sidesFine-tuning the selected picture mode Using the preset and user modesSelecting a preset mode Using the remote controlRenaming user modes Setting the User 1/User 2/User 3 modeResetting the picture mode Enter and ExitFine-tuning the picture quality Advanced picture quality controls Setting Black LevelSelecting a color temperature Controlling image clarityTo adjust and store the settings Setting a preferred color temperatureTo set a preferred color temperature Color ManagementAdjusting contrast ratio via Iris Adjusting Brilliant ColorSelecting a Gamma setting Using the remote controlSelecting the aspect ratio Their original width using this settingAbout the aspect ratio Operating in a high altitude environment Using Panamorph lenses optionalTo activate High Altitude Mode Suitable for use with PC and Rgbhd source inputsPIP source conflict list Disabled functions for the active windowsDisplaying more than one image source simultaneously Highlight PIP and press / to select OnPersonalizing the projector menu display Creating your own startup screenLocking control keys Turning the power off Commands during the cooling processOn-Screen Display OSD menus On-Screen Display OSD structureSetup System SetupInformation Picture -- Basic menu Picture -- Advanced menuSystem Setup menu Display menuAdvanced Setup menu Source ResolutionInformation menu Lamp HoursAdditional information Care of the projectorTo clean the filter Resetting the filter timerGetting to know the lamp hour Setting Auto OffLamp information Extending lamp lifeTiming of replacing the lamp Replacing the lampTighten the screws securing the lamp box Pulling it too quickly may cause the lamp toResetting the lamp timer After the startup logo, press Menu and then press / untilIndicators Troubleshooting Optical SpecificationsDimensions ElectricalTiming chart Format Resolution Refresh rateHz Freq.KHz Pixel Freq.MHzSupported timing for Hdmi input Supported timing for Video and S-Video inputsCopyright Warranty and Copyright informationWarranty DisclaimerEEC statement for European users Regulation statementsFCC statement for United States users MIC statement
Top Page Image Contents