BenQ W5000, W20000 Using the projector, Turning the projector on, Selecting an input source

Page 19

W20000-en.book Page 19 Monday, October 22, 2007 3:35 PM

Using the projector

Preparations

1.Plug in and turn all of the connected equipment on.

2.If not already in, plug the supplied power cable into the AC inlet on the rear of the projector and turn on the power switch.

3.Plug the power cable into a wall socket and turn the wall switch on.

Turning the projector on

Follow the steps below.

1.Make sure the Power light is orange after power has been applied and the main AC power switch is turned on.

2.Press and hold POWER ( ) on the projector or remote control to turn the projector on.

3.The fans will start operating, and a start-up image displays on the screen for a few seconds while it warms up.

4.If you are prompted for a password, press the arrow keys to enter a six digit password. See "Utilizing the password function" on page 21 for details.

5."Source Searching..." will be displayed on the screen before the projector identifies the input signal. This message will remain on the screen until a valid signal is detected. See "Selecting an input source" on page 19 for details.

6.If the horizontal frequency of the input signal exceeds the range of the projector, the message "Out of Range" will be displayed on the screen. This message will remain on-screen until you change the input signal to an appropriate source.

The projector will not respond to further commands while it is warming up.

English

Selecting an input source

The projector can be connected to multiple equipment at the same time. When the projector is first turned on, it will attempt to reconnect with the input source which was in use when the projector was last shut down.

To select the video source:

Using the remote control or projector

Press one of the Source buttons on the remote control, or press SOURCE on the projector repeatedly until your desired signal is selected. To switch between HDMI 1 and HDMI 2, press HDMI 1.2 again.

Using the OSD menu

1.Press MENU and then press / until the System Setup menu is highlighted.

2.Press to highlight Input Source and press ENTER. The source selection bar displays.

3.Press / repeatedly until your desired signal is selected and press

ENTER.

Once detected, the selected source information will display on the screen for seconds. If there is multiple equipment connected to the projector, you can go back to the source selection bar again to search for other signals.

If you want the projector to automatically search for the signals, select On in the System Setup > Auto Source Search menu.

If you want to use the PIP function, see "Displaying more than one image source simultaneously" on page 32 for details.

System Setup

Language

English

Splash Screen

BenQ

My Screen

 

Projector Position

Floor Front

Auto Off

Disable

Sleep Timer

Disable

Background Color

Blue

Menu Settings

 

Input Source

ENTER

Auto Source Search

On

S-Video

EXIT Back

 

 

 

 

HDMI 1

 

 

 

 

 

HDMI 2

 

 

Video

 

 

S-Video

 

 

Component 1

 

 

Component 2

 

 

RGB HD

 

Using the projector

19

Image 19
Contents W20000/W5000 Digital Projector Home Cinema Series WelcomeTable of contents Important safety instructions During operation. It may harm your sight Do not block the ventilation holes whileDo not step on the projector or place any objects upon it Ceiling mounting the projector Moisture condensationAvoid volatile liquid DisposalOverview Shipping contentsRemote control batteries Remote control operationProjector features Rear view Connector panelProjector exterior view Front and upper side viewControl panel Controls and functionsRemote control Choosing a location Positioning your projectorShifting the projection lens vertically Obtaining a preferred projected image sizeDetermine the aspect ratio of your screen, 169 or 43? With min Position Zoom Cm C Cm D Projection dimensionsInstallation for a 169 ratio screen Widescreen ratio screen dimension tableMin Max Highest Lowest Image Installation for a 43 ratio screenDiagonal Better video quality Connecting with video equipmentPreparations Best video qualityConnecting Rgbhv devices Connecting Hdmi devicesConnecting component-video devices Connecting a computer Connecting S-Video or video devicesConnect the projector to a computer with a VGA-BNC cable Turning the projector on Using the projectorUsing the remote control or projector Using the OSD menuAdjust the projected picture to the size that you Using the menusFine-tuning the image size and clarity Use / to highlight the System Setup menuIf you forget the password Using a security cable lockUtilizing the password function Setting a passwordConfirm the new password by re-entering the new password Entering the password recall procedureChanging the password Disabling the password functionTwo parallel sides Adjusting the projected imageAdjusting the projection angle Correcting picture distortionUsing the remote control Using the preset and user modesSelecting a preset mode Fine-tuning the selected picture modeEnter and Exit Setting the User 1/User 2/User 3 modeResetting the picture mode Renaming user modesFine-tuning the picture quality Controlling image clarity Setting Black LevelSelecting a color temperature Advanced picture quality controlsColor Management Setting a preferred color temperatureTo set a preferred color temperature To adjust and store the settingsUsing the remote control Adjusting Brilliant ColorSelecting a Gamma setting Adjusting contrast ratio via IrisSelecting the aspect ratio Their original width using this settingAbout the aspect ratio Suitable for use with PC and Rgbhd source inputs Using Panamorph lenses optionalTo activate High Altitude Mode Operating in a high altitude environmentHighlight PIP and press / to select On Disabled functions for the active windowsDisplaying more than one image source simultaneously PIP source conflict listPersonalizing the projector menu display Creating your own startup screenLocking control keys Commands during the cooling process Turning the power offOn-Screen Display OSD structure On-Screen Display OSD menusSetup System SetupInformation Picture -- Advanced menu Picture -- Basic menuDisplay menu System Setup menuAdvanced Setup menu Lamp Hours ResolutionInformation menu SourceCare of the projector Additional informationResetting the filter timer To clean the filterExtending lamp life Setting Auto OffLamp information Getting to know the lamp hourReplacing the lamp Timing of replacing the lampPulling it too quickly may cause the lamp to Tighten the screws securing the lamp boxAfter the startup logo, press Menu and then press / until Resetting the lamp timerIndicators Troubleshooting Electrical SpecificationsDimensions OpticalFormat Resolution Refresh rateHz Freq.KHz Pixel Freq.MHz Timing chartSupported timing for Video and S-Video inputs Supported timing for Hdmi inputDisclaimer Warranty and Copyright informationWarranty CopyrightMIC statement Regulation statementsFCC statement for United States users EEC statement for European users