BenQ W20000, W5000 user manual Connecting S-Video or video devices, Connecting a computer

Page 18

W20000-en.book Page 18 Monday, October 22, 2007 3:35 PM

English

Connecting S-Video or video devices

From audio output	To audio input
terminals	terminals
	HDMI
	Y	PB/CB PR/CR	S-
	Y	PB/CB PR/CR	VIDEO
S-Video cable	G/Y B/PB/CB R/PR/CR H	V	RS-232
or			12V
or

Video cable

You need only connect S-Video or composite Video cable from the same device, never both at the same time. You should also connect the separate audio cable to a suitable audio amplifier.

If you have already made a Component Video connection between the projector and the video source device, you need not connect to this device again using an S-Video or composite Video connection as this makes an unnecessary second connection of poorer picture quality. You need only connect using a composite Video connection if both Component Video and S-Video are not supplied on the video source device (for example, with some analog video cameras).

Connecting a computer

Connect the projector to a computer with a VGA-BNC cable.

Laptop or desktop computer

From audio output	To audio input
terminals	terminals

HDMI
			Y	PB/CB PR/CR	S-VIDEO
			Y	PB/CB PR/CR	VIDEO
G/Y	B/PB/CB	R/PR/CR	H	V	RS-232
					12V TRIGGER

VGA-BNC cable

If the selected video image is not displayed after the projector is turned on and the correct video source has been selected, please check that the video source device is turned on and operating correctly. Also check that the signal cables have been connected correctly.

Many laptops do not turn on their external video ports when connected to a projector. Usually a key combination like Fn + F3 or CRT/LCD key turns the external display on/off. Locate a function key labeled CRT/LCD or a function key with a monitor symbol on the laptop. Press Fn and the labeled function key simultaneously. Refer to your laptop’s documentation to discover your laptop’s key combination.

18 Connecting with video equipment

Image 18

Contents Welcome W20000/W5000 Digital Projector Home Cinema SeriesTable of contents Important safety instructions Do not block the ventilation holes while During operation. It may harm your sightDo not step on the projector or place any objects upon it Disposal Moisture condensationAvoid volatile liquid Ceiling mounting the projectorRemote control operation Shipping contentsRemote control batteries OverviewProjector features Front and upper side view Connector panelProjector exterior view Rear viewControls and functions Control panelRemote control Positioning your projector Choosing a locationObtaining a preferred projected image size Shifting the projection lens verticallyDetermine the aspect ratio of your screen, 169 or 43? Widescreen ratio screen dimension table Projection dimensionsInstallation for a 169 ratio screen With min Position Zoom Cm C Cm DInstallation for a 43 ratio screen Min Max Highest Lowest ImageDiagonal Best video quality Connecting with video equipmentPreparations Better video qualityConnecting Hdmi devices Connecting Rgbhv devicesConnecting component-video devices Connecting S-Video or video devices Connecting a computerConnect the projector to a computer with a VGA-BNC cable Using the OSD menu Using the projectorUsing the remote control or projector Turning the projector onUse / to highlight the System Setup menu Using the menusFine-tuning the image size and clarity Adjust the projected picture to the size that youSetting a password Using a security cable lockUtilizing the password function If you forget the passwordDisabling the password function Entering the password recall procedureChanging the password Confirm the new password by re-entering the new passwordCorrecting picture distortion Adjusting the projected imageAdjusting the projection angle Two parallel sidesFine-tuning the selected picture mode Using the preset and user modesSelecting a preset mode Using the remote controlRenaming user modes Setting the User 1/User 2/User 3 modeResetting the picture mode Enter and ExitFine-tuning the picture quality Advanced picture quality controls Setting Black LevelSelecting a color temperature Controlling image clarityTo adjust and store the settings Setting a preferred color temperatureTo set a preferred color temperature Color ManagementAdjusting contrast ratio via Iris Adjusting Brilliant ColorSelecting a Gamma setting Using the remote controlTheir original width using this setting Selecting the aspect ratioAbout the aspect ratio Operating in a high altitude environment Using Panamorph lenses optionalTo activate High Altitude Mode Suitable for use with PC and Rgbhd source inputsPIP source conflict list Disabled functions for the active windowsDisplaying more than one image source simultaneously Highlight PIP and press / to select OnCreating your own startup screen Personalizing the projector menu displayLocking control keys Turning the power off Commands during the cooling processOn-Screen Display OSD menus On-Screen Display OSD structureSystem Setup SetupInformation Picture -- Basic menu Picture -- Advanced menuSystem Setup menu Display menuAdvanced Setup menu Source ResolutionInformation menu Lamp HoursAdditional information Care of the projectorTo clean the filter Resetting the filter timerGetting to know the lamp hour Setting Auto OffLamp information Extending lamp lifeTiming of replacing the lamp Replacing the lampTighten the screws securing the lamp box Pulling it too quickly may cause the lamp toResetting the lamp timer After the startup logo, press Menu and then press / untilIndicators Troubleshooting Optical SpecificationsDimensions ElectricalTiming chart Format Resolution Refresh rateHz Freq.KHz Pixel Freq.MHzSupported timing for Hdmi input Supported timing for Video and S-Video inputsCopyright Warranty and Copyright informationWarranty DisclaimerEEC statement for European users Regulation statementsFCC statement for United States users MIC statement