BenQ W5000, W20000 Adjusting Brilliant Color, Selecting a Gamma setting, Using the remote control

Page 29

W20000-en.book Page 29 Monday, October 22, 2007 3:35 PM

Adjusting Brilliant Color

This feature utilizes a new color-processing algorithm and system level enhancements to enable higher brightness while providing truer, more vibrant colors in picture. When set to "Off", Brilliant Color is disabled.

Selecting a Gamma setting

Highlight Gamma Selection and select a preferred setting by pressing / on the projector or remote control.

Gamma refers to the relationship between input source and picture brightness.

Gamma 2.2

Increases the average brightness of the picture. Best for a lit environment, meeting room or family room.

Gamma 2.4/2.5

Best for viewing movies in a darken environment.

Gamma 2.6/2.8

Best for viewing movies which are mostly composed of dark scenes.

High Brightness

Low Brightness

Low Contrast

High Contrast

Picture -- Advanced

Black Level

0 IRE

Clarity Control

 

Color Temperature

Normal

Color Temperature User_ Fine

Gamma Selection

2.4

Brilliant Color

On

Color Management

 

Dynamic Black

On

IRIS

0

Lens Shift

 

S-Video

EXIT Back

Picture -- Advanced

Black Level

0 IRE

Clarity Control

 

Color Temperature

Normal

Color Temperature User_ Fine

Gamma Selection

2.4

Brilliant Color

On

Color Management

 

Dynamic Black

On

IRIS

0

Lens Shift

 

S-Video

EXIT Back

English

2.2 2.4 2.5 2.6 2.8

Adjusting contrast ratio via IRIS

The contrast ratio is the measurement of the difference between the brightest whites and the darkest blacks a display can show. This projector has a very high contrast ratio which can reveal subtle color detail not possible with projectors which have a lower contrast ratio. You can adjust the contrast level to allow for ambient lighting levels within the room which may affect color detail. Make sure Dynamic Black in the Picture -- Advanced menu is set to "On" before you can adjust the contrast ratio.

To manually adjust the contrast ratio,

Using the remote control

1.Press IRIS. The adjustment bar displays.

2.Press to lower the contrast and increase brightness, or press to raise the contrast and decrease brightness.

Using the OSD menu

1.Press MENU and then press / until the Picture -- Advanced menu is highlighted.

2.Press to highlight IRIS.

3.Press to lower the contrast and increase brightness, or press to raise the contrast and decrease brightness.

Picture -- Advanced

Black Level

0 IRE

Clarity Control

 

Color Temperature

Normal

Color Temperature User_ Fine

Gamma Selection

2.4

Brilliant Color

On

Color Management

 

Dynamic Black

On

IRIS

0

Lens Shift

 

S-Video

EXIT Back

Picture -- Advanced

Black Level

 

 

0 IRE

Clarity Control

 

 

 

 

Color Temperature

 

 

Normal

Color Temperature User_ Fine

Gamma Selection

2.4

Brilliant Color

 

 

On

Color Management

 

 

 

 

Dynamic Black

 

 

On

IRIS

+ 8

 

 

 

Lens Shift

 

 

 

 

S-Video

 

 

EXIT Back

Using the projector

29

Image 29
Contents W20000/W5000 Digital Projector Home Cinema Series WelcomeTable of contents Important safety instructions Do not step on the projector or place any objects upon it Do not block the ventilation holes whileDuring operation. It may harm your sight Avoid volatile liquid Moisture condensationDisposal Ceiling mounting the projectorRemote control batteries Shipping contentsRemote control operation OverviewProjector features Projector exterior view Connector panelFront and upper side view Rear viewControl panel Controls and functionsRemote control Choosing a location Positioning your projectorShifting the projection lens vertically Obtaining a preferred projected image sizeDetermine the aspect ratio of your screen, 169 or 43? Installation for a 169 ratio screen Projection dimensionsWidescreen ratio screen dimension table With min Position Zoom Cm C Cm DDiagonal Installation for a 43 ratio screenMin Max Highest Lowest Image Preparations Connecting with video equipmentBest video quality Better video qualityConnecting component-video devices Connecting Hdmi devicesConnecting Rgbhv devices Connect the projector to a computer with a VGA-BNC cable Connecting S-Video or video devicesConnecting a computer Using the remote control or projector Using the projectorUsing the OSD menu Turning the projector onFine-tuning the image size and clarity Using the menusUse / to highlight the System Setup menu Adjust the projected picture to the size that youUtilizing the password function Using a security cable lockSetting a password If you forget the passwordChanging the password Entering the password recall procedureDisabling the password function Confirm the new password by re-entering the new passwordAdjusting the projection angle Adjusting the projected imageCorrecting picture distortion Two parallel sidesSelecting a preset mode Using the preset and user modesFine-tuning the selected picture mode Using the remote controlResetting the picture mode Setting the User 1/User 2/User 3 modeRenaming user modes Enter and ExitFine-tuning the picture quality Selecting a color temperature Setting Black LevelAdvanced picture quality controls Controlling image clarityTo set a preferred color temperature Setting a preferred color temperatureTo adjust and store the settings Color ManagementSelecting a Gamma setting Adjusting Brilliant ColorAdjusting contrast ratio via Iris Using the remote controlAbout the aspect ratio Their original width using this settingSelecting the aspect ratio To activate High Altitude Mode Using Panamorph lenses optionalOperating in a high altitude environment Suitable for use with PC and Rgbhd source inputsDisplaying more than one image source simultaneously Disabled functions for the active windowsPIP source conflict list Highlight PIP and press / to select OnLocking control keys Creating your own startup screenPersonalizing the projector menu display Commands during the cooling process Turning the power offOn-Screen Display OSD structure On-Screen Display OSD menusInformation System SetupSetup Picture -- Advanced menu Picture -- Basic menuDisplay menu System Setup menuAdvanced Setup menu Information menu ResolutionSource Lamp HoursCare of the projector Additional informationResetting the filter timer To clean the filterLamp information Setting Auto OffGetting to know the lamp hour Extending lamp lifeReplacing the lamp Timing of replacing the lampPulling it too quickly may cause the lamp to Tighten the screws securing the lamp boxAfter the startup logo, press Menu and then press / until Resetting the lamp timerIndicators Troubleshooting Dimensions SpecificationsOptical ElectricalFormat Resolution Refresh rateHz Freq.KHz Pixel Freq.MHz Timing chartSupported timing for Video and S-Video inputs Supported timing for Hdmi inputWarranty Warranty and Copyright informationCopyright DisclaimerFCC statement for United States users Regulation statementsEEC statement for European users MIC statement