BenQ W5000, W20000 user manual Important safety instructions

Page 3

W20000-en.book Page 3 Monday, October 22, 2007 3:35 PM

Thank you for your purchase of this quality BenQ video projector! It has been designed to provide you with an enjoyable home theater viewing experience. For the best results, please read this manual through carefully as it is your guide through the control menus and operation.

Important safety instructions

Your projector is designed and tested to meet the latest standards for safety of information technology equipment. However, to ensure safe use of this product, it is important that you follow the instructions mentioned in this manual and marked on the product.

English

1.Please read this user manual before you operate 4. your projector. Keep this manual in a safe place for future reference.

2.Always place the projector on a level, horizontal surface during operation.

-Do not place the projector on an unstable cart, stand, or table as it may fall and be damaged;

-Do not place inflammables near the projector;

-Do not use if tilted at an angle of more than 10 degrees left to right, nor at angle of more than 15 degrees front to back.

3.Do not store the projector on end vertically. Doing so may cause the projector to fall over, causing injury or resulting in damage.

Do not place the projector in any of the following environments:

-space that is poorly ventilated or confined. Allow at least 50 cm clearance from walls and free flow of air around the projector;

-locations where temperatures may become excessively high, such as the inside of a car with all windows closed;

-locations where excessive humidity, dust, or cigarette smoke may contaminate optical components, shortening the projector’s lifespan and darkening the screen;

-locations near fire alarms;

-locations with an ambient temperature above 35°C/95°F;

-locations where altitude is higher than 1500 meters/4920 feet above sea level.

4920-

9840

feet

Important safety instructions

3

Image 3
Contents W20000/W5000 Digital Projector Home Cinema Series WelcomeTable of contents Important safety instructions Do not block the ventilation holes while During operation. It may harm your sightDo not step on the projector or place any objects upon it Ceiling mounting the projector Moisture condensationAvoid volatile liquid DisposalOverview Shipping contentsRemote control batteries Remote control operationProjector features Rear view Connector panelProjector exterior view Front and upper side viewControl panel Controls and functionsRemote control Choosing a location Positioning your projectorShifting the projection lens vertically Obtaining a preferred projected image sizeDetermine the aspect ratio of your screen, 169 or 43? With min Position Zoom Cm C Cm D Projection dimensionsInstallation for a 169 ratio screen Widescreen ratio screen dimension tableInstallation for a 43 ratio screen Min Max Highest Lowest ImageDiagonal Better video quality Connecting with video equipmentPreparations Best video qualityConnecting Hdmi devices Connecting Rgbhv devicesConnecting component-video devices Connecting S-Video or video devices Connecting a computerConnect the projector to a computer with a VGA-BNC cable Turning the projector on Using the projectorUsing the remote control or projector Using the OSD menuAdjust the projected picture to the size that you Using the menusFine-tuning the image size and clarity Use / to highlight the System Setup menuIf you forget the password Using a security cable lockUtilizing the password function Setting a passwordConfirm the new password by re-entering the new password Entering the password recall procedureChanging the password Disabling the password functionTwo parallel sides Adjusting the projected imageAdjusting the projection angle Correcting picture distortionUsing the remote control Using the preset and user modesSelecting a preset mode Fine-tuning the selected picture modeEnter and Exit Setting the User 1/User 2/User 3 modeResetting the picture mode Renaming user modesFine-tuning the picture quality Controlling image clarity Setting Black LevelSelecting a color temperature Advanced picture quality controlsColor Management Setting a preferred color temperatureTo set a preferred color temperature To adjust and store the settingsUsing the remote control Adjusting Brilliant ColorSelecting a Gamma setting Adjusting contrast ratio via IrisTheir original width using this setting Selecting the aspect ratioAbout the aspect ratio Suitable for use with PC and Rgbhd source inputs Using Panamorph lenses optionalTo activate High Altitude Mode Operating in a high altitude environmentHighlight PIP and press / to select On Disabled functions for the active windowsDisplaying more than one image source simultaneously PIP source conflict listCreating your own startup screen Personalizing the projector menu displayLocking control keys Commands during the cooling process Turning the power offOn-Screen Display OSD structure On-Screen Display OSD menusSystem Setup SetupInformation Picture -- Advanced menu Picture -- Basic menuDisplay menu System Setup menuAdvanced Setup menu Lamp Hours ResolutionInformation menu SourceCare of the projector Additional informationResetting the filter timer To clean the filterExtending lamp life Setting Auto OffLamp information Getting to know the lamp hourReplacing the lamp Timing of replacing the lampPulling it too quickly may cause the lamp to Tighten the screws securing the lamp boxAfter the startup logo, press Menu and then press / until Resetting the lamp timerIndicators Troubleshooting Electrical SpecificationsDimensions OpticalFormat Resolution Refresh rateHz Freq.KHz Pixel Freq.MHz Timing chartSupported timing for Video and S-Video inputs Supported timing for Hdmi inputDisclaimer Warranty and Copyright informationWarranty CopyrightMIC statement Regulation statementsFCC statement for United States users EEC statement for European users