BenQ W5000, W20000 user manual Advanced Setup menu

Page 39

W20000-en.book Page 39 Monday, October 22, 2007 3:35 PM

 

Menu Display Time (15 sec)

Menu Settings

Sets the length of time the OSD will remain active after your last key press. The

range is from 5 to 30 seconds in 5-second increments.

 

Menu Position (Center)

 

Sets the On-Screen Display (OSD) menu position.

 

 

Input Source

Selects an input source to be projected. See "Selecting an input source" on page 19

for details.

 

 

 

Auto Source Search

Sets whether the projector searches automatically for input sources. If the source

(Off)

scan is On, the projector will scan for input sources until it acquires a signal. If the

function is not activated, the projector selects the last used input source.

 

 

 

Advanced Setup menu

FUNCTION

DESCRIPTION

(default setting / value)

 

 

Lamp Power (Normal)

 

Selects the projector lamp between Normal and Whisper modes.

 

Lamp Hours

Lamp

Shows the lamp hours information. See "Getting to know the lamp hour" on

page 43 for details.

 

 

Reset Lamp Timer

 

Once the lamp is renewed, select Reset to return the lamp timer to '0'. See

 

"Resetting the lamp timer" on page 46 for details.

 

 

 

Grid

 

Press ENTER to display the grid test pattern. It helps you adjust the image size and

Pattern

focus and check that the projected image is free of distortion.

Color Bar

 

 

Press ENTER to display the color bar test pattern. You can display this test pattern

 

to check that the colors are to your liking.

 

 

 

Dust Filter Hours

Dust Filter

Shows the dust filter hours information

Reset Dust Filter Timer

 

 

Resets the duster filter timer to '0'. See "To clean the filter" on page 42 for details.

 

 

High Altitude Mode

A mode for operation in areas like high altitude or high temperature. See

(Off)

"Operating in a high altitude environment" on page 31 for details.

 

 

 

Password (Off)

 

Limits use of the projector to only those who know the correct password. See

Password

"Utilizing the password function" on page 21 for details.

Change Password

 

 

You will be asked to enter the current password before changing to a new one. See

 

"Utilizing the password function" on page 21 for details.

 

 

Key Lock

Locks the keys on the projector and remote control except POWER and EXIT. See

"Locking control keys" on page 33 for details.

 

 

 

 

Returns all settings to the factory preset values.

Reset All Settings

The following settings will still remain: Names of user modes, Keystone,

 

Position, H.Size, Phase, Language, Projector Position, High Altitude

 

Mode, Lamp, and Password.

Using the projector

39

English

Page 38 Page 40
Image 39
Page 38 Page 40
Contents W20000/W5000 Digital Projector Home Cinema Series WelcomeTable of contents Important safety instructions Do not block the ventilation holes while During operation. It may harm your sightDo not step on the projector or place any objects upon it Ceiling mounting the projector Moisture condensationAvoid volatile liquid DisposalOverview Shipping contentsRemote control batteries Remote control operationProjector features Rear view Connector panelProjector exterior view Front and upper side viewControl panel Controls and functionsRemote control Choosing a location Positioning your projectorShifting the projection lens vertically Obtaining a preferred projected image sizeDetermine the aspect ratio of your screen, 169 or 43? With min Position Zoom Cm C Cm D Projection dimensionsInstallation for a 169 ratio screen Widescreen ratio screen dimension tableInstallation for a 43 ratio screen Min Max Highest Lowest ImageDiagonal Better video quality Connecting with video equipmentPreparations Best video qualityConnecting Hdmi devices Connecting Rgbhv devicesConnecting component-video devices Connecting S-Video or video devices Connecting a computerConnect the projector to a computer with a VGA-BNC cable Turning the projector on Using the projectorUsing the remote control or projector Using the OSD menuAdjust the projected picture to the size that you Using the menusFine-tuning the image size and clarity Use / to highlight the System Setup menuIf you forget the password Using a security cable lockUtilizing the password function Setting a passwordConfirm the new password by re-entering the new password Entering the password recall procedureChanging the password Disabling the password functionTwo parallel sides Adjusting the projected imageAdjusting the projection angle Correcting picture distortionUsing the remote control Using the preset and user modesSelecting a preset mode Fine-tuning the selected picture modeEnter and Exit Setting the User 1/User 2/User 3 modeResetting the picture mode Renaming user modesFine-tuning the picture quality Controlling image clarity Setting Black LevelSelecting a color temperature Advanced picture quality controlsColor Management Setting a preferred color temperatureTo set a preferred color temperature To adjust and store the settingsUsing the remote control Adjusting Brilliant ColorSelecting a Gamma setting Adjusting contrast ratio via IrisTheir original width using this setting Selecting the aspect ratioAbout the aspect ratio Suitable for use with PC and Rgbhd source inputs Using Panamorph lenses optionalTo activate High Altitude Mode Operating in a high altitude environmentHighlight PIP and press / to select On Disabled functions for the active windowsDisplaying more than one image source simultaneously PIP source conflict listCreating your own startup screen Personalizing the projector menu displayLocking control keys Commands during the cooling process Turning the power offOn-Screen Display OSD structure On-Screen Display OSD menusSystem Setup SetupInformation Picture -- Advanced menu Picture -- Basic menuDisplay menu System Setup menuAdvanced Setup menu Lamp Hours ResolutionInformation menu SourceCare of the projector Additional informationResetting the filter timer To clean the filterExtending lamp life Setting Auto OffLamp information Getting to know the lamp hourReplacing the lamp Timing of replacing the lampPulling it too quickly may cause the lamp to Tighten the screws securing the lamp boxAfter the startup logo, press Menu and then press / until Resetting the lamp timerIndicators Troubleshooting Electrical SpecificationsDimensions OpticalFormat Resolution Refresh rateHz Freq.KHz Pixel Freq.MHz Timing chartSupported timing for Video and S-Video inputs Supported timing for Hdmi inputDisclaimer Warranty and Copyright informationWarranty CopyrightMIC statement Regulation statementsFCC statement for United States users EEC statement for European users
Top Page Image Contents